We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Blue industrial pin and sleeve plug with watertight gasketed housing

Hubbell Incorporated

Hubbell Incorporated HBL430P9W Watertight Pin & Sleeve Plug 30 A 250V AC

SKU CH-3MDB-A49J2

A 30 A, 250 V AC three-phase IEC pin-and-sleeve plug with a Zytel 801 nylon housing, IP67 watertight seal and screw terminals for 12–8 AWG cable

  • Color/FinishBlue
  • Color MappingBlue
  • TypeLight Switch
  • Watertight IP67 and NEMA 4X seal for harsh environments
  • 30 A 250 V AC three-phase power delivery
  • Zytel 801 nylon housing resists impact and chemicals
  • Accepts 0.5 to 1.25 in cables with 12–8 AWG wire
  • Operates from –40 °C to +75 °C with CSA and UL certifications

30 A 250 V AC industrial plug

The Hubbell HBL430P9W is a watertight pin-and-sleeve plug rated for 30 amps at 250 V AC. It is built for three-phase, four-wire circuits in industrial and commercial settings where moisture resistance is required. The non-metallic housing uses Zytel 801 nylon for impact resistance. A gasketed sealing ring provides the watertight seal.

Capacity and headroom

The device accepts cables from .5 in to 1.25 in diameter and wire sizes from 12 AWG minimum to 8 AWG maximum. It operates across a temperature range of -40 °C to +75 °C. The NEMA 4X and IP67 ratings confirm suitability for wet and dusty environments. It is not intended for applications exceeding 30 A or voltages above 250 V AC.

Build quality and daily use

The straight-orientation body features screw terminals for secure conductor termination. An IEC grounded configuration ensures proper earthing in three-phase installations. Compliance includes CSA C22.2 No. 182.1, UL E146032 and UL IEC 60309-1 listing. The shrouded, non-metallic design resists corrosion and impact during routine connection and disconnection.

Highlights

  • Watertight IP67 and NEMA 4X seal for harsh environments
  • 30 A 250 V AC three-phase power delivery
  • Zytel 801 nylon housing resists impact and chemicals
  • Accepts 0.5 to 1.25 in cables with 12–8 AWG wire
  • Operates from –40 °C to +75 °C with CSA and UL certifications

Specifications

BrandHUBBELL
Color/FinishBlue
Color MappingBlue
TypeLight Switch

Questions about this item

Will the 30 A 250V AC rating match the 30 A circuit breaker I already have installed?

Yes, the plug is rated for 30 A at 250V AC, so it aligns with a 30 A breaker; ensure the breaker is also rated for 250V AC and the wiring uses 12 to 8 AWG conductors.

How can I verify the watertight seal is effective after wiring the plug?

Confirm the gasketed sealing ring is fully seated, tighten the cable gland onto a cable within the .5 to 1.25 in diameter range, and check that the NEMA 4X and IP67 markings are present on the housing.

What cable and wire sizes does the plug accept, and are terminals included?

The plug accepts cables from .5 to 1.25 in diameter and wire sizes from 12 AWG minimum to 8 AWG maximum; screw terminals are built into the plug for direct connection.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.