We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Red round clearance marker lamp, 2 inch diameter, bracket mount with grommet

Grote

Grote 45822 Clearance Marker Lamp Red 2 in

SKU CH-CTPK-3QDKX

Red incandescent clearance lamp with 2 in diameter, bracket or grommet mount, and PL-10 connector for FMVSS 108 compliance

  • ColorRed
  • Meets FMVSS 108 and SAE P2/PC safety standards
  • Incandescent lamp draws only .33 amp for low power use
  • Seal-Tight gasket keeps moisture and debris out of the lens
  • Round 2-inch red lens gives clear side-marker visibility
  • PL-10 connector fits Grote models 66800, 66801, 66840, 66850, 66851, 67001, 67050

Grote 45822 Clearance Marker Lamp

The Grote 45822 is a round, red clearance marker lamp built for recreational vehicles and trailers that require FMVSS 108 compliance. Its two-inch diameter and bracket-and-grommet mount let it fit standard marker-light openings on side and rear panels. The incandescent lamp draws 0.33 A and uses a PL-10 connector that mates with Grote harness models 66800, 66801, 66840, 66850, 66851, 67001 and 67050. It is not suited for applications that demand LED service life or a different lens colour.

Thermals, noise and power draw

Incandescent operation produces noticeable heat at the lens surface during extended use, so the lamp should not contact heat-sensitive trim. There are no moving parts, so the unit runs silently in normal service. Electrical draw is a steady 0.33 A at system voltage, placing minimal load on the vehicle charging circuit. Builders who need lower heat or lower current should consider alternative lamp types not covered by this listing.

Bundled accessories and software

The lamp ships with a Seal-Tight expanded rubber gasket that seals the mounting hole against water and road spray when installed in a compatible grommet. No wiring harness, connector, or mounting hardware is included; the compatible connector series listed above must be sourced separately. There is no software or programmable feature associated with this lamp. Installers who expect a complete plug-and-play kit will need to purchase the appropriate harness and grommet separately.

Highlights

  • Meets FMVSS 108 and SAE P2/PC safety standards
  • Incandescent lamp draws only .33 amp for low power use
  • Seal-Tight gasket keeps moisture and debris out of the lens
  • Round 2-inch red lens gives clear side-marker visibility
  • PL-10 connector fits Grote models 66800, 66801, 66840, 66850, 66851, 67001, 67050

Specifications

BrandGROTE
ColorRed

Questions about this item

How do I mount the 45822 lamp and which step is often missed?

Secure the bracket or grommet first, then plug the PL-10 connector into a compatible 66800-series pigtail; the step most people skip is seating the Seal-Tight expanded rubber gasket fully so moisture cannot enter.

What maintenance or replacement will the 45822 need over time?

The incandescent bulb will eventually burn out; when it does, replace the entire sealed lamp assembly because the lens and housing are not serviceable separately.

What limit appears first during extended operation of the 45822?

Continuous duty at 0.33 A causes the filament to heat until it fails, so bulb life is the first constraint under sustained use.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.