We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Small rectangular SFP+ transceiver module with duplex LC port, matte metal finish, 100 km single-mode label

Ficer Technology Co., Ltd

Ficer Technology Co., Ltd 10G SFP+ Transceiver 100KM 1550nm (Commercial Temperature)

SKU CH-QPAG-1R3WM

A 10 Gbps single-mode SFP+ transceiver with 1550 nm wavelength and 100 km reach for long-haul Ethernet links

  • Device TypeTransceiver
  • Fiber CableSingle-mode Optical Fiber
  • Ports10GBASE-ZR/ZW Ethernet
  • Transfer Rate10 Gbps
  • 10 Gbps throughput over 100 km single-mode fiber
  • 1550 nm wavelength enables long-haul transmission
  • Hot-pluggable SFP+ form factor for easy deployment
  • Duplex LC connector ensures reliable fiber links
  • TAA-compliant manufacturing in Taiwan for regulated projects

100 km single-mode transceiver

The Ficer 10G SFP+ module delivers 10 Gbps over single-mode fibre at 1550 nm for link distances up to 100 km. It suits network engineers extending campus or metro Ethernet links where long-haul reach is required. The hot-pluggable design fits standard SFP+ cages without powering down the switch.

MSA compliance and custom coding

The transceiver follows the SFF-8431 SFP+ MSA and SFF-8472 diagnostics interface, enabling monitoring of temperature, voltage and optical power. Units are coded on request for Cisco, Juniper or other open switches, so the module identifies correctly in the host equipment. A duplex LC connector and single 3.3 V supply simplify installation.

Verify switch coding and fibre type

Confirm the target switch accepts third-party SFP+ modules and provide the vendor and model so the correct EEPROM coding can be programmed. Ensure the cabling plant uses single-mode fibre with LC duplex patch cords rated for the full 100 km span. Check that the link budget matches the 1550 nm wavelength before ordering.

Highlights

  • 10 Gbps throughput over 100 km single-mode fiber
  • 1550 nm wavelength enables long-haul transmission
  • Hot-pluggable SFP+ form factor for easy deployment
  • Duplex LC connector ensures reliable fiber links
  • TAA-compliant manufacturing in Taiwan for regulated projects

Specifications

Device TypeTransceiver
Fiber CableSingle-mode Optical Fiber
Ports10GBASE-ZR/ZW Ethernet
Transfer Rate10 Gbps

Questions about this item

Will the 1550 nm laser or LC connector need replacement after long-term 100 km runs?

The module uses a 1550 nm transmitter and duplex LC connector rated for the full 100 km link; no user-serviceable parts are specified, so replacement would only be needed if the transceiver itself fails.

What limits continuous 10 Gbps throughput over the 100 km single-mode link?

The optical budget for 100 km at 1550 nm and the 10 Gbps line rate set the practical ceiling; sustained use stays within the IEEE 802.3 ae and SFF-8431 specifications.

How much power does the transceiver draw and what heat should I expect in a 3.3 V switch slot?

It operates from a single 3.3 V supply with hot-plug support; power draw follows the SFP+ MSA limits, so heat contribution inside the switch is minimal.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.