We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
A small green circuit board with a 20-pin Type-E plug and two 9-pin USB 2.0 headers, plus a USB Type-A cable attached

Fervit

Fervit USB 3.1 Type-E to Dual 9-Pin USB 2.0 Header Adapter

SKU CH-TS65-8XV46

Converts a motherboard USB 3.1 Type-E header into two 9-pin USB 2.0 headers with a built-in hub chip running at 480Mbps and 500mA per port

  • Converts a 20-pin Type-E header into two 9-pin USB 2.0 headers
  • Built-in USB 2.0 hub chipset delivers 480 Mbps per port
  • Each port supplies 500 mA at 5 V for reliable device power
  • Adhesive backing lets you secure the module to the motherboard or chassis
  • Plug-and-play design needs no extra cables or drivers

Fervit USB 3.1 Type-E to Dual 9-Pin Adapter

This adapter converts a motherboard USB 3.1 Type-E header into two standard 9-pin USB 2.0 headers. It includes a Type-E cable, a Type-A cable, and a PCBA module with an integrated USB 2.0 hub chipset. Builders can connect front-panel USB 2.0 devices or internal accessories without occupying additional motherboard headers. The compact design plugs directly into the 20-pin Type-E connector and requires no extra mounting hardware.

Thermals noise and power draw

The adapter draws power from the motherboard header and supplies up to 500 mA at 5 V to each of the two 9-pin ports. Passive operation means no fan noise and no measurable heat output during normal use. Total bandwidth is limited to 480 Mbps by the USB 2.0 hub chipset, so power consumption remains low and steady. The included adhesive backing allows secure placement on the motherboard or chassis.

Single specification that decides fit

The product only works if your motherboard provides a 20-pin USB 3.1 Type-E internal header. Boards with only standard 19-pin USB 3.0 headers or older 9-pin USB 2.0 headers cannot accept the Type-E plug. Buyers who need to split a regular USB 3.0 header or add USB 3.0 speed ports should look for a different adapter.

Highlights

  • Converts a 20-pin Type-E header into two 9-pin USB 2.0 headers
  • Built-in USB 2.0 hub chipset delivers 480 Mbps per port
  • Each port supplies 500 mA at 5 V for reliable device power
  • Adhesive backing lets you secure the module to the motherboard or chassis
  • Plug-and-play design needs no extra cables or drivers

Specifications

BrandFervit

Questions about this item

How do I install the Type-E cable onto a 20pin motherboard header and where does the adhesive-backed PCBA go?

Align the Type-E plug with the 20pin USB 3.1 header, press straight down until seated, then peel the backing on the PCBA and stick it to the motherboard or chassis for a fixed mount.

What ongoing maintenance does the onboard USB 2.0 hub chipset need?

No scheduled maintenance is required; the hub chipset is passive and has no replaceable parts, so only reseat the cables if a port stops responding.

At what point does the 500ma per-port current limit throttle connected devices under sustained load?

Each 9pin port supplies up to 500ma at 5v; drawing more will cause the port to current-limit or shut down until the load drops.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.