EN-Labs
EN-Labs SATA 15-pin to 6× TX4 PWM splitter cable 16.9 inch
A sleeved SATA 15-pin to six TX4 PWM splitter cable, 16.9 inches long, powers six fans from one PSU connector while one motherboard header controls speed and reports RPM for all
- TypePWM fan power cable
- ColorBlack
- Length16.9 inches
- Cable Length16.9 inches
- Connector ASATA 15pin
- Connector BPWM 4pin
- Powers up to six fans from one SATA 15-pin PSU connector
- Single motherboard header controls PWM speed for all connected fans
- Only one fan reports RPM preventing signal conflicts on the board
- Black sleeved jacket keeps internal wiring tidy and organised
- 9 inch length suits compact and mid-tower chassis layouts
Splitter cable for six PWM fans
This EN-Labs cable splits a single SATA 15-pin power connector from the PSU into six TX4 male connectors for 12 V DC fans. A seventh TX4 female header connects to the motherboard fan header to provide RPM feedback and PWM speed control. The 16.9 inch black sleeved jacket keeps the wiring tidy inside the case.
Builders who want one header to drive six fans
The adapter suits systems where the motherboard has limited fan headers but the PSU has spare SATA power plugs. It is not for 5 V DC fans, and it cannot supply RPM data from more than one fan at a time. Builders needing independent speed curves for each fan should look at a multi-header controller instead.
Steady PWM signal across all six outputs
Because only the female header and one male connector carry the tachometer wire, the motherboard receives a single clean RPM reading while the PWM duty cycle drives all six fans in unison. The SATA power feed delivers 12 V continuously, so fan speed remains stable under sustained load without the voltage sag that can occur on crowded motherboard headers.
Highlights
- Powers up to six fans from one SATA 15-pin PSU connector
- Single motherboard header controls PWM speed for all connected fans
- Only one fan reports RPM preventing signal conflicts on the board
- Black sleeved jacket keeps internal wiring tidy and organised
- 9 inch length suits compact and mid-tower chassis layouts
Specifications
| Brand | En-Labs |
|---|---|
| Type | PWM fan power cable |
| Color | Black |
| Length | 16.9 inches |
| Cable Length | 16.9 inches |
| Connector A | SATA 15pin |
| Connector B | PWM 4pin |
| Connector Number | 8 |
| Features | SATA to 4-pin PWM Fan Power Splitter Adapter Converter Cable gives you a simple, cost-effective way to connect multiple computer case fans to a single motherboard fan header. The black sleeved jacket not only enhances cable management, but also provides a sleeker look that seamlessly integrates into the interior of any case. The SATA6TX443CM features one 15-pin SATA male connector at one end for connection to your computer PSU, and offers six TX4 male connectors and one TX4 female connector at the other end, which allows for easy connection up to six PWM fans at the same time. For PW |
Questions about this item
What power supply connector is required to run this SATA 15-pin to 6× TX4 PWM splitter cable?
The cable draws power from a standard SATA 15-pin connector on your power supply, delivering 12 V DC to all attached fans.
Can the six TX4 male connectors drive both 3-pin and 4-pin fans already installed in my case?
Yes, each male TX4 header accepts either 3-pin or 4-pin fans; only one fan reports RPM while the rest follow the shared PWM signal.
How do I verify that PWM speed control and RPM feedback are working after I connect everything?
Plug the single TX4 female header into a motherboard fan header; the BIOS or monitoring software should then show one RPM reading that changes with load.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
Black Box Corporation
Black Box Corporation CAT6 EZ-RJ45 Modular Plugs 100-Pack
$95.99
0.00115015BTC
In stock
