We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Silver-grey aluminium fin heatsink with copper pipe and thermal pads for 2280 M.2 SSD

EN-Labs

EN-Labs M.2 2280 SSD Heat Sink 6mm Copper Pipe 32 Fins 14.8 W/m.K Pads

SKU CH-7RDE-R5B6J

Cools 2280 M.2 SSDs with a 6 mm copper heat pipe, 32 aluminum fins and 14.8 W/m.K thermal pads for 10–30 °C lower temperatures

  • Cools M.2 2280 SSD 10°C–30°C using 6 mm copper heat pipe and 32 aluminium fins
  • 8 W/m.K double-sided thermal pads (1.0 mm and .5 mm) transfer heat fast
  • Passive aluminium electroplated fin stack and base need no fan or power
  • Fits 2280 form factor (79 × 24 × 48 mm) for NVME or SATA drives
  • Groove-design alloy body maximises surface area for silent, zero-maintenance cooling

M.2 2280 SSD heat sink for NVME or SATA drives

This passive cooler fits the 2280 form factor and uses a 6 mm copper heat pipe with 32 aluminium fins to draw heat away from the controller and NAND. It is intended for builders who want to prevent thermal throttling on high-speed SSDs without adding a fan.

Aluminium alloy body with electroplated base

The 79×24×48 mm assembly combines a pure aluminium electroplated base, a stainless-steel mounting plate and a grooved fin design that increases surface area. Double-sided 1.0 mm and 0.5 mm silicone pads rated at 14.8 W/m.K ensure full contact on both sides of the drive.

Check motherboard clearance

The heat sink adds height above the M.2 slot, so verify that your board has enough space between the slot and any adjacent components or heatsinks. It only supports the 80 mm 2280 length; shorter 2230 or 2242 modules will not mount correctly.

Highlights

  • Cools M.2 2280 SSD 10°C–30°C using 6 mm copper heat pipe and 32 aluminium fins
  • 8 W/m.K double-sided thermal pads (1.0 mm and .5 mm) transfer heat fast
  • Passive aluminium electroplated fin stack and base need no fan or power
  • Fits 2280 form factor (79 × 24 × 48 mm) for NVME or SATA drives
  • Groove-design alloy body maximises surface area for silent, zero-maintenance cooling

Specifications

No published specifications for this item yet.

Questions about this item

Does the 6 mm AGHP heat pipe and 32 aluminium fins limit the cooler to PCIe NVMe or SATA M.2 2280 drives?

The heatsink is built for the 2280 form factor and works with both NVMe and SATA M.2 SSDs; the copper pipe and fin stack do not restrict the electrical interface.

Will the 79 × 24 × 48 mm cooler clear a motherboard heatsink or tall components next to the M.2 slot?

At 48 mm tall and 24 mm wide it sits above most board-mounted shields, but verify your specific board layout because the stainless-steel base plate adds thickness.

Which of the included 1.0 mm and 0.5 mm thermal pads goes on the controller side and which on the NAND side during installation?

Place the 1.0 mm pad on the controller side and the 0.5 mm pad on the NAND side; using the wrong thickness on either side is the most common fitment error.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.