EN-Labs
EN-Labs LP423TX425CM Molex to 3×4-pin fan power splitter cable 10 in black sleeved
Splits one Molex connector into three 4-pin fan headers for 12 V power only, 10 in black sleeved cable
- Typefan power splitter cable
- ColorBlack
- Length10 inch / 25CM
- Cable Length10 in.
- SpecificationsName: Black Sleeved 4pin IDE Molex to three 3Pin/4Pin Fan po
- Connector AMolex IDE 4pin
- Powers three fans from one Molex connector
- Black sleeved 10-inch cable keeps build tidy
- 12 V output only — no PWM speed control
- 2-wire fan headers fit 3-pin and 4-pin plugs
- Single Molex to triple 4-pin splitter expands cooling options
Molex-to-three-fan splitter
The EN-Labs LP423TX425CM cable splits a single 4-pin Molex connector from a power supply into three 4-pin fan headers. It is built for system builders who need to run multiple case or CPU cooler fans from one PSU lead. The black sleeved wiring keeps the loom tidy inside the chassis. Each output header uses only two wires to deliver 12 V DC power.
Three fans at fixed 12 V
The adapter powers up to three fans simultaneously at a constant 12 volts. Because the connectors carry only power pins, the motherboard cannot regulate speed through PWM or monitor RPM feedback. Fans will run at full speed unless they have their own internal controller. The 10 inch length suits typical mid-tower routing from PSU to fan cluster.
Passive operation and no speed control
No active electronics are present, so the cable adds no audible noise or measurable heat of its own. Power draw equals the combined current of the attached fans, limited by the Molex source and the 2-wire 12 V design. Builders who need variable fan curves should use motherboard headers instead of this fixed-voltage splitter.
Highlights
- Powers three fans from one Molex connector
- Black sleeved 10-inch cable keeps build tidy
- 12 V output only — no PWM speed control
- 2-wire fan headers fit 3-pin and 4-pin plugs
- Single Molex to triple 4-pin splitter expands cooling options
Specifications
| Brand | EN-Lab |
|---|---|
| Model | LP423TX425CM |
| Type | fan power splitter cable |
| Color | Black |
| Length | 10 inch / 25CM |
| Cable Length | 10 in. |
| Specifications | Name: Black Sleeved 4pin IDE Molex to three 3Pin/4Pin Fan power adapter cable IDE : 2pin Male Fan 4Pin connector: 2pin Male tips Material: Black Sleeved Output voltage: 12V Length: Approx. 10 inch / 25cm Note: Just power adapter cable get power from PSU,It doesn't support PWM fan speed controlling |
| Connector A | Molex IDE 4pin |
| Connector B | 3 x 4pin fan male (2pin tips) |
| Connector Number | 4 |
| Features | This EN-Labs LP423TX425CM power splitter cable is intended for connection of 3 ports 4-Pin PWM device (CPU cooler, case fan...) to a PSU power connector (4-Pin Molex). Black Sleeved 4pin IDE Molex to three 3Pin/4Pin cooler case / PWM Fan power splitter adapter cable It is usually used for converting PC PSU IDE molex 4pin to three 3Pin/4Pin fan connector |
Questions about this item
Will the 4-pin Molex connector on this LP423TX425CM cable fit the older power supply I am keeping?
Yes, the cable uses a standard 4-pin Molex IDE connector that plugs into any ATX power supply with a matching Molex output.
How can I confirm the splitter is delivering power to all three fans after I install it?
Connect each fan to the three 4-pin headers; if all fans spin at full speed on 12 V DC, the splitter is working as intended.
Does the 10-inch sleeved cable include the three case fans or only the adapter?
Only the Molex-to-three-fan splitter cable is included; the fans themselves must be purchased separately.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
Black Box Corporation
Black Box Corporation CAT6 EZ-RJ45 Modular Plugs 100-Pack
$95.99
0.00114981BTC
In stock
