We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Twenty silver aluminium heatsinks, 14 by 14 by 6 mm, with adhesive tape

EN-Labs

EN-Labs 20pcs Aluminium Heatsink 14x14x6mm w/ 3M 9448a Tape diy cooling

SKU CH-FJFQ-7T75V

Pack of 20 aluminium heatsinks sized 14x14x6mm with pre-applied 3M 9448 thermal tape for chipset cooling

  • ColorSilver
  • CompatibilityMotherboard Chipsets
  • MaterialAluminium
  • FeaturesWidely use for 3D Printer A4988 chipset,computer PC chipset,
  • Dimensions14*14*6mm
  • Cools A4988 stepper drivers with 14 mm aluminium
  • Pre-attached 3M 9448a tape speeds installation
  • Twenty pieces cover multiple boards in one pack
  • Fits Raspberry Pi, motherboard and GPU chipsets
  • Pure aluminium fins lower overheating risk

20-piece aluminium heatsink kit for small ICs

This kit contains twenty aluminium heatsinks each measuring 14 by 14 by 6 millimetres. They are intended for motherboard chipsets, power ICs, LED devices and single-board computers such as Raspberry Pi, Banana Pi and Orange Pi. The parts help lower operating temperature and reduce the risk of hardware failure caused by overheating.

Peel-and-stick 3M 9448a tape simplifies fitting

Every heatsink comes with pre-applied 3M 9448a thermal double-sided adhesive tape. Installation is a matter of cleaning the component surface, peeling the liner and pressing the heatsink into place. The tape can be separated later with a razor blade so the heatsink lifts off without damaging the underlying chip.

14 by 14 by 6 millimetre footprint decides fit

The single specification that determines compatibility is the 14 by 14 by 6 millimetre outline of each heatsink. Buyers must verify that their target component and the available clearance match these exact dimensions before ordering. Builders needing a larger contact area or a taller profile will need a different solution.

Highlights

  • Cools A4988 stepper drivers with 14 mm aluminium
  • Pre-attached 3M 9448a tape speeds installation
  • Twenty pieces cover multiple boards in one pack
  • Fits Raspberry Pi, motherboard and GPU chipsets
  • Pure aluminium fins lower overheating risk

Specifications

ColorSilver
CompatibilityMotherboard Chipsets
MaterialAluminium
FeaturesWidely use for 3D Printer A4988 chipset,computer PC chipset, power IC, power electric device, LED light devices,Raspberry Pi,Banan Pi, Orange Pi,etc,reduce the risk of hardware failure due to overheating.
These pure aluminum heat sinks include adhesive thermal tape for efficient thermal transfer to the heat sink providing additional cooling to the IC. Also, it is easy to remove with a razor blade, so you can remove the heatsink without damaging the chips.
Size is 14mm x 14mm x6mm,Please check the specification table and make sure that the size of the heatsink fits that of your compon
Dimensions14*14*6mm

Questions about this item

How can I verify the heatsink is working after attaching it to a chip?

Monitor the chip temperature under load; a working heatsink will keep it lower than before installation.

What does the 20-piece pack contain and what extra items are needed?

The pack includes 20 aluminium heatsinks measuring 14 x 14 x 6 mm with 3M 9448a thermal tape pre-applied; no extra parts are required for basic mounting.

Which heatsink size should I choose for an A4988 driver on a 3D printer?

The 14 x 14 x 6 mm size matches the A4988 chipset footprint; confirm your chip dimensions before ordering.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.