EN-Labs
EN-Labs 10pcs Aluminum Heatsink 8.8x8.8x5mm 3M 8810 diy cooling
Pack of ten 8.8 mm aluminium heatsinks with pre-applied 3M 8810 thermal tape for chipset, Raspberry Pi or LED cooling
- ColorSilver
- CompatibilityMotherboard Chipsets
- MaterialAluminium
- Features10 pcs of 8.8x8.8x5mm aluminum heat sinks with 3M 8810 Heat
- Dimensions8.8mm x 8.8mm x 5mm
- 10-piece kit covers multiple chips on one board
- 8 mm square footprint fits tight component spacing
- 3M 8810 tape bonds with pressure alone — no curing needed
- 6 W/m-k thermal conductivity moves heat into the aluminium
- Suits A4988 drivers, Raspberry Pi SoCs and similar ICs
Aluminium Heatsink Kit
This pack contains ten aluminium heatsinks sized 8.8mm x 8.8mm x 5mm, each supplied with a pre-cut piece of 3M 8810 thermally conductive adhesive tape. The square profile suits small surface-mount chips such as stepper drivers, voltage regulators and single-board-computer processors. The pressure-sensitive tape bonds on contact without a cure cycle, simplifying installation for hobbyists and repair technicians.
Adhesive Interface Limits
The 3M 8810 tape provides a thermal conductivity of .6 W/m-k and doubles as an electrical insulator, so it can be applied directly to exposed circuitry. Because the bond relies on pressure alone, the mating surfaces must be clean and reasonably flat for the adhesive to wet properly. The tape softens slightly to accommodate minor unevenness, but large gaps or heavily textured packages will reduce thermal transfer.
Capacity and Headroom
Ten heatsinks give enough units for a typical 3D-printer control board or a cluster of Raspberry Pi, Banana Pi or Orange Pi modules. Each sink adds a modest fin area to dissipate heat from low-power ICs such as the A4988 stepper driver or similar voltage regulators. The small 5mm height restricts airflow in tight enclosures, so sustained high-current loads may still require active cooling or larger heatsinks.
Highlights
- 10-piece kit covers multiple chips on one board
- 8 mm square footprint fits tight component spacing
- 3M 8810 tape bonds with pressure alone — no curing needed
- 6 W/m-k thermal conductivity moves heat into the aluminium
- Suits A4988 drivers, Raspberry Pi SoCs and similar ICs
Specifications
| Color | Silver |
|---|---|
| Compatibility | Motherboard Chipsets |
| Material | Aluminium |
| Features | 10 pcs of 8.8x8.8x5mm aluminum heat sinks with 3M 8810 Heat transfer Peel and Stick Tape Widely use for 3D Printer A4988 chipset,computer PC chipset, power IC, power electric device, LED light devices,Raspberry Pi,Banan Pi, Orange Pi,etc. Come with 3M 8810, is a tacky pressure sensitive adhesive loaded with thermally conductive ceramic fillers that do not require a heat cure cycle to form an excellent bond to many substrates. Only pressure is needed to form an excellent bond and thermal interface. The specialized chemistry of 3M 8810 renders the tape modestly soft and able to wet to |
| Dimensions | 8.8mm x 8.8mm x 5mm |
Questions about this item
How many heatsinks are included in the pack?
The pack contains 10 aluminium heatsinks, each measuring 8.8mm by 8.8mm by 5mm, with pre-applied 3M 8810 adhesive tape.
What does the 0.6 W/m-k rating mean for my chip temperature?
The 3M 8810 tape conducts heat at up to 0.6 W/m-k, forming a pressure-activated bond that moves heat from the chip into the aluminium without needing a curing cycle.
Does the 3M 8810 tape require heat to cure, and what surfaces does it stick to?
No heat cure is needed; firm pressure alone creates a strong thermal and adhesive bond to flat or slightly uneven metal, ceramic or plastic surfaces.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
Black Box Corporation
Black Box Corporation CAT6 EZ-RJ45 Modular Plugs 100-Pack
$95.99
0.0011546BTC
In stock
