We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Four silver stainless steel worm-drive hose clamps in a bag

EesTeck HPC 4" Stainless Steel Hose Clamps 4-Pack

SKU CH-11YG-8AGYG

Four 304 stainless steel worm-drive clamps adjust from 91 to 114 mm to seal 4-inch hoses in plumbing, automotive or industrial systems

  • TypeHPC, Bag
  • Tube Size4" -4Pcs
  • Item Count4 pack
  • Thread Size4" -4Pcs
  • End Connections4" -4Pcs
  • Body MaterialStainless Steel
  • 304 stainless steel resists rust and corrosion for long service life
  • Worm-drive screw adjusts from 91 mm to 114 mm to fit 3.5–4 inch hoses
  • Bolted open-ring design locks tight under torsion and pressure for leak-free seals
  • Four clamps in one pack cover multiple connections in plumbing or automotive jobs
  • Loosen or tighten with a screwdriver for quick installation and removal

4-Inch 304 Stainless Steel Hose Clamps

These four 304 stainless steel worm-drive clamps fit hose diameters from 91 mm to 114 mm. The 3.5-inch to 4-inch adjustment range suits automotive, industrial, marine and general plumbing lines. Each clamp uses a bolt-tightened open ring for a secure, leak-resistant seal on rubber, silicone or metal hose.

Replacing Worn or Undersized Clamps

Swap out corroded mild-steel bands or clamps that no longer hold pressure on 4-inch ducting, coolant or intake hose. The 304 alloy resists rust and chemical attack where standard zinc-plated hardware fails. The wide adjustment span covers multiple hose wall thicknesses without needing a different part number.

Build Integration and Clearance

The slim band profile sits close to the hose OD, leaving room in tight engine bays, duct runs or bilge areas. A standard screwdriver or nut driver tightens the worm gear; no special tools are required. Buyers needing clamps below 91 mm or above 114 mm should select a different diameter from the same series.

Highlights

  • 304 stainless steel resists rust and corrosion for long service life
  • Worm-drive screw adjusts from 91 mm to 114 mm to fit 3.5–4 inch hoses
  • Bolted open-ring design locks tight under torsion and pressure for leak-free seals
  • Four clamps in one pack cover multiple connections in plumbing or automotive jobs
  • Loosen or tighten with a screwdriver for quick installation and removal

Specifications

TypeHPC, Bag
Tube Size4" -4Pcs
Item Count4 pack
Thread Size4" -4Pcs
End Connections4" -4Pcs
Body MaterialStainless Steel
Pipe Size4" -4Pcs
Compatibility/Fitment4" -4Pcs
Size/Dimensions4" -4Pcs
FinishStainless Steel
Selling UnitSet
Commercial/ResidentialIndustrial
BrandEesTeck
ModelHPC
FeaturesIndustrial
Part Number84-108

Questions about this item

What hose diameter range does the 4-inch clamp cover?

The 4-inch worm-drive clamps adjust from 91 mm to 114 mm, fitting hoses with an outer diameter between 3.5 inches and 4 inches.

Which tool and step are needed to install the clamp correctly?

Use a screwdriver to loosen the worm screw, slide the band over the hose, then tighten until the band grips evenly without over-torquing the bolt.

When should the 304 stainless steel clamps be inspected or replaced?

Check the band and screw threads periodically for corrosion or thread wear; replace any clamp that no longer holds torque or shows pitting on the 304 steel.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.