We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green rectangular circuit board with gold PCIe edge connector and silver heatsink, no mounting bracket

DELL

DELL PERC V10 Z0017A SAS-SATA RAID Controller No Bracket N4C2D 5R10N

SKU CH-9ACJ-DN36M

Adds SAS and SATA RAID 0, 1, 5, 6, 10, 50 to Dell PowerEdge servers via PCIe 3.0 x8 at 12 Gbps

  • Compatible ManufacturerFor Dell
  • Compatible ModelsFor Dell PowerEdge Server Series
  • Dimensions6.6" x 2.7" x 0.7"
  • Weight0.15 lbs
  • Supports RAID 0, 1, 5, 6, 10, 50 for flexible data protection
  • PCI-E 3.0 x8 interface delivers 12 GBPS transfer rate
  • Works with SAS and SATA HDDs and SSDs for broad drive compatibility
  • Designed for Dell PowerEdge servers ensuring validated integration
  • Compact 6.6" x 2.7" x 0.7" card weighs 0.15 lbs

Dell PERC V10 RAID Controller for PowerEdge

The Dell PERC V10 Z0017A is a SAS-SATA RAID controller card built for Dell PowerEdge servers. It connects through a PCI-E 3.0 x8 slot and delivers a 12 GBPS data transfer rate. The card manages both SAS and SATA hard drives and solid-state drives. Part numbers N4C2D and 5R10N identify this new component.

Suits Dell server upgrades without a bracket

This controller fits administrators expanding storage on compatible PowerEdge systems using existing drive cages. It supports RAID 0, 1, 5, 6, 10 and 50 for redundancy and performance. Buyers needing an included mounting bracket or installing into non-Dell chassis should verify fitment first. The low-profile dimensions are 6.6" x 2.7" x 0.7" and it weighs 0.15 lbs.

RAID level support decides the fit

The single specification that determines suitability is the RAID level support: RAID 0, 1, 5, 6, 10 and 50. If your deployment requires one of these levels on SAS or SATA drives, this card matches. If a different RAID mode or drive interface is needed, this controller will not meet the requirement.

Highlights

  • Supports RAID 0, 1, 5, 6, 10, 50 for flexible data protection
  • PCI-E 3.0 x8 interface delivers 12 GBPS transfer rate
  • Works with SAS and SATA HDDs and SSDs for broad drive compatibility
  • Designed for Dell PowerEdge servers ensuring validated integration
  • Compact 6.6" x 2.7" x 0.7" card weighs 0.15 lbs

Specifications

BrandDell
Part Number5R10N
Compatible ManufacturerFor Dell
Compatible ModelsFor Dell PowerEdge Server Series
Dimensions6.6" x 2.7" x 0.7"
Weight0.15 lbs

Questions about this item

Will this card fit a PCI-E 3.0 x8 slot in my server?

Yes, the controller uses a PCI-E 3.0 x8 interface and measures 6.6" x 2.7" x .7", so it installs in any compatible x8 slot.

Can I connect my existing 6 Gbps SATA SSDs to this controller?

The card supports both SAS and SATA HDDs and SSDs at up to 12 GBPS per port, so 6 Gbps SATA drives will operate at their native speed.

How do I verify the RAID 10 array is healthy after installation?

Use the PERC V10 management utility or BIOS configuration utility to confirm the virtual disk shows Optimal status and all member drives report Ready.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.