We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black square amplifier chassis with silver front panel controls and rear connection terminals

Dayton Audio

Dayton Audio SPA250 250W Subwoofer Amplifier

SKU CH-3ZTD-5FSWR

A 250 watt subwoofer amplifier with variable low-pass filter from 40 to 180 Hz, switchable phase and bass boost at 35 Hz

  • TypeAmplified Subwoofers
  • Precise bass control with variable low-pass filter from 40 Hz to 180 Hz at 24 dB/octave
  • Flexible system integration via switchable 0° or 180° phase adjustment
  • Clean signal handling through 10.4K ohm input impedance and 90 dB signal-to-noise ratio
  • Reliable power delivery with 252 watts RMS into 4 ohms at 1.0% THD
  • Space-saving installation using 8-1/2 inch square cutout dimensions

Amplified Subwoofer for Home Integration

The Dayton Audio SPA250 is a mono Class AB subwoofer amplifier designed to add low-frequency reinforcement to existing audio systems. It accepts both low-level and high-level inputs, allowing connection to virtually any source or receiver. Manual, auto, and triggered on/off modes simplify integration with automated setups. Energy-efficient standby draws less than one watt.

Power Delivery into Typical Loads

Measured output reaches 156 watts RMS into 8 ohms at .1 percent THD and 252 watts RMS into 4 ohms at under 1.0 percent THD. The damping factor sits at 114 at 100 Hz, indicating firm cone control. Switchable mains voltage covers 115 and 230 VAC at 50 or 60 Hz. Builders needing significantly more power into 2-ohm loads should consider other options.

Crossover and Phase Flexibility

A variable low-pass filter adjusts from 40 Hz to 180 Hz at 24 dB per octave, while a switchable subsonic filter provides 12 dB per octave high-pass at 20 Hz. Phase can be set to 0 or 180 degrees, and a 6 dB bass boost at 35 Hz is selectable. Speaker-level high-pass outputs operate at 6 dB per octave, approximately 180 Hz at 4 ohms and 90 Hz at 8 ohms.

Highlights

  • Precise bass control with variable low-pass filter from 40 Hz to 180 Hz at 24 dB/octave
  • Flexible system integration via switchable 0° or 180° phase adjustment
  • Clean signal handling through 10.4K ohm input impedance and 90 dB signal-to-noise ratio
  • Reliable power delivery with 252 watts RMS into 4 ohms at 1.0% THD
  • Space-saving installation using 8-1/2 inch square cutout dimensions

Specifications

TypeAmplified Subwoofers

Questions about this item

Should I run this amplifier at 4 ohms or 8 ohms for the most power?

The amplifier delivers 252 watts RMS into 4 ohms at less than 1.0% THD and 156 watts RMS into 8 ohms at 0.1% THD, so 4 ohms gives higher output.

What does the 250-watt rating mean when the amp is driving a real subwoofer?

Measured output is 252 watts RMS into 4 ohms at under 1.0% THD and 156 watts RMS into 8 ohms at 0.1% THD, so actual continuous power depends on the load you connect.

What inputs and outputs does the SPA250 provide for connecting to my system?

It has low-level and high-level inputs plus line-level full-bandwidth outputs for daisy-chaining, and speaker-level high-pass outputs at 6 dB/octave (180 Hz at 4 ohms, 90 Hz at 8 ohms).

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.