We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Graphite metallic sleeved ATX PCI-E wire with female connectors on both ends, 17.5 inches long

Darkside

Darkside DS-0656 17.5" 45cm Female-Female Pre-Sleeved ATX PCI-E Wire Graphite Metallic

SKU CH-4TQM-9N99H

Pre-sleeved ATX and PCI-E wires with factory-crimped female pins on both ends, 45 cm long in graphite metallic, simplify custom power-cable builds

  • FeaturesTake the sleeving and pin crimping out of custom PC cabling.
  • Pre-crimped ATX pins remove the need for manual crimping
  • 5-inch length suits mid-tower and larger chassis builds
  • Graphite Metallic sleeving gives a consistent, professional cable appearance
  • Female-to-female connectors plug directly into standard ATX and PCI-E housings
  • Over 20 colour options let you match or contrast any build theme

Custom cable wire for DIY builders

The Darkside DS-0656 is a pre-sleeved ATX and PCI-E wire with female terminals on both ends. It removes the need to sleeve or crimp individual conductors when assembling custom power cables. The graphite metallic finish suits colour-coordinated builds. It is sold as a single 45 cm length for modular cable projects.

Replaces bulk sleeving and loose pins

This wire replaces the raw sleeving, loose terminals and hand-crimping steps normally required for custom ATX cables. The jump is worth it when a builder wants consistent pin placement and uniform colour without investing in crimp tools or learning termination technique. It also saves time when re-pinning existing modular cables for a new colour scheme.

Simple push-in installation with removal tool

Each end pushes into standard ATX connector housings until the terminal latches. A Billy Brown extraction tool is recommended if a wire is seated in the wrong position, as the retention tabs are difficult to release by hand. No soldering or heat-shrink is required, but builders must verify pin-out compatibility with their specific power supply before seating the terminals.

Highlights

  • Pre-crimped ATX pins remove the need for manual crimping
  • 5-inch length suits mid-tower and larger chassis builds
  • Graphite Metallic sleeving gives a consistent, professional cable appearance
  • Female-to-female connectors plug directly into standard ATX and PCI-E housings
  • Over 20 colour options let you match or contrast any build theme

Specifications

BrandDarkside
Model712190092566
Part NumberDS-0656
FeaturesTake the sleeving and pin crimping out of custom PC cabling.

Questions about this item

What length and connector type does this 45 cm wire use for ATX and PCI-E builds?

The DS-0656 is a 17.5 inch (45 cm) female-to-female pre-sleeved wire with standard ATX pins crimped on both ends, ready for ATX and PCI-E connector housings.

Which tool is recommended if I insert a pin into the wrong position on the connector?

A Billy Brown Tool is recommended to release and remove an incorrectly seated ATX pin from the connector housing without damaging the crimp or sleeve.

Will the graphite metallic sleeving fray or need re-sleeving after repeated routing?

The wire arrives pre-sleeved in graphite metallic; the sleeving is fixed over the crimped pins, so it does not require re-sleeving unless the sleeve itself is physically cut or abraded during installation.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.