We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Folding knife with 3.7 inch Damascus steel blade camel bone handle brass mosaic pin leather sheath

Damascus Depot

Damascus Depot Folding Knife 3.7" Blade Camel Bone Handle 8.25" Overall

SKU CH-X9RB-HM1HT

A hand-forged Damascus steel folding knife with a 3.7 inch blade, camel bone handle scales, brass and mosaic pin hardware, a liner lock, and an included thick cowhide leather sheath

  • TypeFolding Knives
  • Blade Length3.7 Inch
  • Overall Length8.2 Inch
  • MaterialDamascus Steel
  • SheathIncluded
  • Blade MaterialDamascus steel
  • Damascus steel blade hardened to 56–58 HRC for lasting edge retention
  • 1095 and 15N20 layered steel creates distinctive twist pattern
  • Camel bone handle with engraved steel bolster and brass pins
  • Liner lock and thumb pin give secure one-hand operation
  • Thick cowhide leather sheath with belt loop included

Hand-Forged Damascus Folding Knife

The Damascus Depot folding knife is a hand-forged custom piece built for outdoor users who value traditional materials. Its blade is crafted from 1095 and 15N20 high and low carbon steel folded into a twist pattern. The handle uses camel coloured bone scales secured with brass screws and a mosaic pin. A thick cowhide leather sheath with a belt loop is included for carry.

Thermals Noise Power Draw

As a manual folding knife, this product generates no heat, produces no audible noise and draws no electrical power during use. Performance depends entirely on the user's technique and the maintenance of the cutting edge. The blade hardness is rated at 56 to 58 HRC following heat treatment.

Sustained Load Behaviour

Under sustained cutting tasks the high-carbon Damascus blade holds its edge well but requires diligent care to prevent corrosion. The supplier advises cleaning and oiling the blade after each use and warns against long-term storage in the leather sheath, which can trap moisture. The liner lock and thumb pin mechanism secures the 3.7 inch blade during heavy work. Not suited for buyers who want a low-maintenance stainless folder or a tool that can be stored wet without attention.

Highlights

  • Damascus steel blade hardened to 56–58 HRC for lasting edge retention
  • 1095 and 15N20 layered steel creates distinctive twist pattern
  • Camel bone handle with engraved steel bolster and brass pins
  • Liner lock and thumb pin give secure one-hand operation
  • Thick cowhide leather sheath with belt loop included

Specifications

BrandDamascus Depot
TypeFolding Knives
Blade Length3.7 Inch
Overall Length8.2 Inch
MaterialDamascus Steel
SheathIncluded
Blade MaterialDamascus steel
Handle MaterialCamel Colored bone

Questions about this item

How do I fit the camel bone handle scales onto the liner-lock folder, and which step causes alignment trouble?

The handle uses two screws, four brass pins and a mosaic pin through the engraved steel bolster; the mosaic pin is the step most people mis-align because it must pass through both scales and the liner simultaneously.

What ongoing care does the 1095/15N20 Damascus blade require to prevent rust?

Clean and dry the 3.7 inch blade after every use, coat it with a light oil or wax, and never store the knife long-term in the leather sheath because the leather traps moisture against the high-carbon steel.

At what hardness does the twist-pattern Damascus edge start to chip under heavy, sustained cutting?

The blade is heat-treated to 56–58 HRC; at that hardness the edge will chip before it rolls if you use it for prying or cutting bone.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.