We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Rectangular lithium-ion camera battery, dark grey finish, connector on one end

Cameron Sino Ti10 Replacement Battery 2500mAh 18.00Wh 7.2V

SKU CH-4C6Z-ZAEK7 MPN Ti10

Replacement lithium-ion battery for Fluke thermal cameras Ti10, Ti20, Ti25, Ti9, TiR and TiR1, 2500 mAh, 18.00 Wh, 7.2 V

  • Compatible with Fluke Ti10, Ti20, Ti25 and TiR thermal cameras
  • 2500 mAh capacity and 18.00 Wh energy for extended field use
  • 2 V lithium-ion pack with fully decoded chip matches original specifications
  • 00 × 27.00 × 29.00 mm, 172.0 g fits original battery compartment
  • Built-in overcharge, over-discharge, over-voltage and short-circuit protection

Compatible Fluke thermal cameras

This replacement battery fits Fluke Ti10, Ti-10, Ti20, Ti-20, Ti20-RBP, Ti25, Ti-25, Ti9, TiR and TiR1 thermal cameras. It replaces original part numbers 3105035, 3524222 and Ti20-RBP. The lithium-ion cell delivers 2500mAh capacity at 7.2V for 18.00Wh total energy.

Who this suits and who it does not

Technicians maintaining the listed Fluke models can use this as a direct swap. Buyers with other thermal camera brands or Fluke models not named above should look elsewhere. The pack measures 100.00 x 27.00 x 29.00mm and weighs 172.0g, so devices with different bay dimensions will not accept it.

Deciding specification

The 7.2V nominal voltage and 2500mAh capacity determine whether this cell matches the original electrical requirements. Verify your camera's part number against 3105035, 3524222 or Ti20-RBP before ordering.

Highlights

  • Compatible with Fluke Ti10, Ti20, Ti25 and TiR thermal cameras
  • 2500 mAh capacity and 18.00 Wh energy for extended field use
  • 2 V lithium-ion pack with fully decoded chip matches original specifications
  • 00 × 27.00 × 29.00 mm, 172.0 g fits original battery compartment
  • Built-in overcharge, over-discharge, over-voltage and short-circuit protection

Specifications

BrandCameron Sino
ModelTi10, Ti-10, Ti20, Ti-20, Ti20-RBP, Ti25, Ti-25, Ti9, TiR, TiR1

Questions about this item

What are the exact dimensions of this 7.2 V 2500 mAh battery so I can confirm it fits my Fluke thermal camera?

The battery measures 100.00 mm by 27.00 mm by 29.00 mm and weighs 172.0 g, matching the original Fluke form factor for Ti10, Ti20, Ti25, Ti9 and TiR series cameras.

Which connector orientation or locking step is most often missed when installing this replacement pack in a Fluke Ti20-RBP?

Align the keyed connector with the camera socket and press firmly until the latch clicks; the decoded chip then communicates instantly with the Fluke firmware.

How should I store the 18.00 Wh lithium-ion pack when the thermal camera will not be used for months?

Keep it at roughly half charge in a dry place below 60 °C; avoid fire, water and disassembly, and cycle it every few months to maintain health.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.