We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Rectangular nickel-zinc battery pack with two wire leads, light-coloured plastic casing, 71 by 50 by 14 mm

Cameron Sino Battery DAITEM Panel Pre 2007 BATNI13 1500mAh 6.0V

SKU CH-VSEE-AZVFY

Replacement nickel-zinc battery for DAITEM Panel Pre 2007, 1500mAh at 6.0V with 71.10 x 50.20 x 14.50mm dimensions

  • Specifications71.10 x 50.20 x 14.50
  • Typenickel_zinc
  • Battery Pack71.10 x 50.20 x 14.50
  • Battery Typenickel_zinc
  • Battery Capacity1500.00 milliamp_hours
  • Battery Voltage6.00 volts
  • Direct replacement for DAITEM Panel Pre 2007 using part number BATNI13
  • 1500 mAh nickel-zinc chemistry delivers 9.00 Wh at 6.0 V
  • Compact 71.10 x 50.20 x 14.50 mm form factor fits original housing
  • ISO9001, RoHS and CE certified with overcharge, over-discharge and short-circuit protection
  • Fully decoded chip works like the original and reaches peak capacity after 2 or 3 cycles

Direct Replacement for DAITEM Panel Pre 2007

This nickel-zinc battery pack matches the original DAITEM BATNI13 specifications with a 1500mAh capacity and 6.0V output. It is built for owners of the Panel Pre 2007 alarm panel who need a new power source that fits the existing compartment. Buyers who need a different voltage or a higher capacity for another model should look elsewhere.

Stable Low-Current Operation

Nickel-zinc chemistry delivers the steady 6.0 volts the panel expects without the voltage sag common in aged cells. The pack weighs 122.0g and measures 71.10 x 50.20 x 14.50mm, so it sits in the original housing without forcing the cover. No active cooling or fan noise is involved because the alarm panel draws only a small standby current.

Ready-to-Install Pack with Protection Circuit

A fully decoded chip communicates with the panel exactly like the factory battery, enabling normal charge and discharge cycles. Integrated safeguards guard against overcharge, over-discharge, over-voltage and short-circuit events. The unit ships in shock-absorbing foam and reaches full performance after two or three complete cycles.

Highlights

  • Direct replacement for DAITEM Panel Pre 2007 using part number BATNI13
  • 1500 mAh nickel-zinc chemistry delivers 9.00 Wh at 6.0 V
  • Compact 71.10 x 50.20 x 14.50 mm form factor fits original housing
  • ISO9001, RoHS and CE certified with overcharge, over-discharge and short-circuit protection
  • Fully decoded chip works like the original and reaches peak capacity after 2 or 3 cycles

Specifications

Brandcameron Sion
ModelDAITEM Panel Pre 2007
Part NumberDAITEM BATNI13
Specifications71.10 x 50.20 x 14.50
Typenickel_zinc
Battery Pack71.10 x 50.20 x 14.50
Battery Typenickel_zinc
Battery Capacity1500.00 milliamp_hours
Battery Voltage6.00 volts

Questions about this item

How do I install this battery in a DAITEM Panel Pre 2007 and which step is often missed?

Slide the pack into the panel until the connector clicks into the BATNI13 socket; the step most people skip is fully seating that connector so the 6.0 V rail makes contact.

What maintenance or replacement will this nickel-zinc 1500 mAh pack need later?

After roughly 2 to 3 full charge-discharge cycles the pack reaches peak capacity; plan to swap it once run-time drops below your alarm system’s minimum 9.00 Wh requirement.

What limit appears first when this 122.0 g battery runs continuously in an alarm panel?

Sustained drain hits the 1500 mAh capacity ceiling first, so the 6.00 V output will sag once the stored 9.00 Wh is depleted.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.