We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Rectangular nickel-zinc battery pack, dark wrap, two wire leads, 59 by 35 by 20 mm

Cameron Sino 2000mAh 2.4V Nickel-Zinc Battery for Autec Light LK4 LK6 LK8

SKU CH-Y1GP-VR98C

Nickel-zinc 2000 mAh 2.4 V replacement pack for Autec Light LK4, LK6 and LK8 crane remotes

  • Specifications59.00 x 35.20 x 20.30
  • Typenickel_zinc
  • Battery Pack59.00 x 35.20 x 20.30
  • Battery Typenickel_zinc
  • Battery Capacity2000.00 milliamp_hours
  • Battery Voltage2.40 volts
  • 2000 mAh capacity extends crane remote run time
  • 4 V nickel-zinc chemistry matches original battery spec
  • Direct replacement for Autec Light LK4, LK6, LK8 models
  • 00 × 35.20 × 20.30 mm form factor fits existing compartment
  • ISO 9001, RoHS and CE certified for safety assurance

Compatible Crane Remote Battery

The Cameron Sino nickel-zinc pack replaces the original power source for Autec Light LK4, LK6 and LK8 crane remote controls. It delivers 2000mAh at 2.4 volts and matches the original dimensions of 59.00 by 35.20 by 20.30 millimetres. The pack weighs 69.0 grams and includes a decoded chip for direct compatibility. Certified to ISO9001, RoHS and CE standards.

Upgrade From Worn Original Cells

This battery replaces an ageing or depleted factory pack that no longer holds a useful charge. The jump is worth it when operating time has dropped noticeably or the remote shuts down under load. A fresh cell restores the full 4.80 watt-hour capacity and the built-in protection against overcharge, over-discharge, over-voltage and short circuit. New cells reach peak performance after two or three full charge cycles.

Check Model And Connector Before Ordering

Verify that your remote is listed as Light LK4, LK6 or LK8 and that the original part number reads ARB-LBM02M or LBM02MH. Confirm the physical size matches 59.00 by 35.20 by 20.30 millimetres so the pack fits the compartment. Ensure the connector polarity aligns with the device socket before installing. Do not use low-quality third-party chargers and avoid storage above 60 degrees Celsius.

Highlights

  • 2000 mAh capacity extends crane remote run time
  • 4 V nickel-zinc chemistry matches original battery spec
  • Direct replacement for Autec Light LK4, LK6, LK8 models
  • 00 × 35.20 × 20.30 mm form factor fits existing compartment
  • ISO 9001, RoHS and CE certified for safety assurance

Specifications

BrandCameron Sino
ModelLight LK4, Light LK6, Light LK8, LK4, LK6, LK8
Part NumberARB-LBM02M, LBM02MH
Specifications59.00 x 35.20 x 20.30
Typenickel_zinc
Battery Pack59.00 x 35.20 x 20.30
Battery Typenickel_zinc
Battery Capacity2000.00 milliamp_hours
Battery Voltage2.40 volts

Questions about this item

Will the 59.00 x 35.20 x 20.30 mm case fit my Autec Light LK6 battery compartment?

The pack measures 59.00 x 35.20 x 20.30 mm and is built to the original specifications for Autec Light LK4, LK6 and LK8 crane remotes.

How do I install it and which step do people miss?

Slide the pack into the remote, then press the connector firmly until it clicks; the step most often missed is not seating the plug fully.

When will the nickel-zinc 2000 mAh cells need replacing?

After roughly 2 to 3 full charge cycles the chemistry stabilises; replace the pack when run-time drops noticeably or the voltage falls below 2.4 V under load.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.