We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
White rectangular lithium battery 50 by 16 by 15 mm

Cameron & Co

Cameron & Co DS-CS-HNW606BT 3.6V 2.7Ah Li-SOCl2 surveillance accessory

SKU CH-D6HV-HJFFF

3.6V 2.7Ah Li-SOCl2 primary battery powers Honeywell wireless magnetic contact 015606 alarm systems

  • TypeBattery
  • Powers Honeywell wireless contact 015606 with 3.6V 2.7Ah Li-SOCl2 cell
  • Delivers 9.72Wh capacity for extended alarm-system runtime
  • Primary non-rechargeable chemistry ensures reliable standby power
  • Compact 50.00 x 16.00 x 15.00 mm form fits device housing
  • 100% OEM-compatible replacement matches original 606BT specifications

Cameron & Co DS-CS-HNW606BT Battery

The Cameron & Co DS-CS-HNW606BT is a 3.6V 2.7Ah lithium thionyl chloride primary cell built for Honeywell wireless magnetic contact 015606 alarm sensors. It supplies 9.72Wh of energy in a 50.00 x 16.00 x 15.00 mm white housing. Security installers and homeowners maintaining compatible Honeywell perimeter devices use this non-rechargeable unit as a direct 100% OEM-compatible replacement.

Sustained load behaviour

Li-SOCl2 chemistry delivers a flat voltage curve across the 2700mAh capacity, so the sensor reports consistent signal strength for the full service interval rather than fading after a high-current burst. The low self-discharge rate supports multi-year deployments in normally closed contacts that only draw microamps until an opening event triggers a transmission. No recharge cycles are possible; the cell is replaced once depleted.

Installation notes

The pack fits the magnetic contact's battery compartment without modification when the polarity markings are observed. A common error is attempting to recharge the primary cell, which can cause leakage or venting. Verify the device part number 15606 before fitting, as similar-looking contacts may use a different voltage or form factor. Dispose of the spent cell according to local lithium battery regulations.

Highlights

  • Powers Honeywell wireless contact 015606 with 3.6V 2.7Ah Li-SOCl2 cell
  • Delivers 9.72Wh capacity for extended alarm-system runtime
  • Primary non-rechargeable chemistry ensures reliable standby power
  • Compact 50.00 x 16.00 x 15.00 mm form fits device housing
  • 100% OEM-compatible replacement matches original 606BT specifications

Specifications

BrandCameron Sino
ModelDS-CS-HNW606BT
TypeBattery

Questions about this item

How much heat or power draw does the 3.6 V 2.7 Ah Li-SOCl2 cell produce when the contact runs continuously?

Primary lithium-thionyl chloride cells generate negligible heat and draw only micro-amps in standby, so the 9.72 Wh unit runs cool for years.

What must I already own for this battery to work in my alarm system?

A Honeywell wireless magnetic contact that accepts part number 015606 — the cell slides into the existing battery compartment.

Will the 50.00 x 16.00 x 15.00 mm form factor fit the older Honeywell contact I already have installed?

Yes, the dimensions match the original 015606 pack, so it drops into legacy contacts without modification.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.