Bogen Communications
Bogen Communications HTA125A 125W car amplifier
Rack-mountable 125 W RMS amplifier with 20–20,000 Hz response and <.5 % THD
- TypeAmplifier
- Other SpecificationsSensitivity: Hi-Z, 500mV; Lo-Z balanced, with optional trans
- Power Output125W RMS
- Frequency Response20-20,000Hz
- THD<0.5% from 20-20,000Hz
- Other ConnectorsTerminal Strip (output) RCA (input) Terminal Strip Balanced
- 125W RMS continuous power for demanding audio systems
- Less than 0.5% total harmonic distortion across 20–20,000 Hz for clean output
- MOSFET design runs cooler and weighs 36.00 lbs for reliable rack mounting
- Multiple output loads including 4Ω, 8Ω, 25V and 70V lines for flexible wiring
- 90dB signal-to-noise ratio keeps background hiss inaudible
125 W RMS rack amplifier
The Bogen Communications HTA125A is a 125 W RMS power amplifier built for rack mounting. It uses power MOSFET circuitry to deliver high efficiency and low heat in a 19.00" x 5.25" x 11.00" chassis weighing 36.00 lbs. The unit accepts hi‑Z unbalanced, lo‑Z balanced and RCA inputs, then drives 4 Ω, 8 Ω, 25 V or 70 V constant‑voltage lines through a terminal strip.
Installers needing multi‑voltage line driving
This amplifier suits commercial audio installers who require a single rack unit to feed both low‑impedance speakers and 25 V or 70 V distributed lines. It is not suited for users who need front‑panel level controls, built‑in signal processing or consumer‑style binding‑post outputs.
125 W RMS into 4 Ω, 8 Ω, 25 V or 70 V loads
The specified 125 W RMS rating applies across all supported output loads: 4 ohms, 8 ohms, 25 V centre‑tap (5 ohms) and 70 V (40 ohms). If the installation demands more than 125 W continuous power, this model will not meet that requirement.
Highlights
- 125W RMS continuous power for demanding audio systems
- Less than 0.5% total harmonic distortion across 20–20,000 Hz for clean output
- MOSFET design runs cooler and weighs 36.00 lbs for reliable rack mounting
- Multiple output loads including 4Ω, 8Ω, 25V and 70V lines for flexible wiring
- 90dB signal-to-noise ratio keeps background hiss inaudible
Specifications
| Brand | Bogen |
|---|---|
| Model | HTA125A |
| Type | Amplifier |
| Other Specifications | Sensitivity: Hi-Z, 500mV; Lo-Z balanced, with optional transformer, 100mV Hum & Noise: 90dB below rated output Output Load: 4 ohms, 8 ohms, 25VCT (5 ohms), 70V (40 ohms) Input Impedance: Hi-Z, 50,000 ohms unbalanced; Lo-Z, 600 ohms, balanced or unbalanced, and 1:1 bridging with optional plug-in transformers Filters: Lo-Cut: -10dB at 100Hz (selectable) Controls: Input level control, circuit breaker reset, lo-cut filter switch, on/off |
| Power Output | 125W RMS |
| Frequency Response | 20-20,000Hz |
| THD | <0.5% from 20-20,000Hz |
| Other Connectors | Terminal Strip (output) RCA (input) Terminal Strip Balanced Lo-Z (input) |
| Dimensions | 19.00" x 5.25" x 11.00" |
| Weight | 36.00 lbs. |
| Shipping weight | 18.39 kg |
| Package size | 556 × 391 × 259 mm |
Questions about this item
Will the 125W RMS output drive my existing 4-ohm speakers cleanly?
Yes, the amplifier delivers 125W RMS into 4 ohms with THD below .5% across 20-20,000Hz.
How do I verify the amplifier is performing correctly once installed?
Measure output at the terminal strip; expect 125W RMS into 4 or 8 ohms with hum and noise 90dB below rated output.
Does the box include the Lo-Z transformer and RCA cables, or must I buy them separately?
The unit provides terminal-strip outputs, RCA input and balanced Lo-Z input terminals; the optional Lo-Z transformer and interconnect cables are not included.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
PAC APH-TY02 Speaker Connection Harness Toyota Lexus 18
- Car Stereo Add-Ons
The Wires Zone Platinum 1/0 AWG Ring Terminals Pair
- Connector and Termi…



