We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black nylon-braided 12VHPWR 90-degree GPU extension cable with three movable zinc-alloy combs, 16-pin male to female connectors

Bipra

Bipra 12VHPWR 90 Degree GPU Extension Cable 600W Type A 2 in 1 accessory

SKU CH-2WY9-NCZXB

A 90-degree 12VHPWR GPU extension cable rated for 600 W with 16 AWG copper wire, movable zinc-alloy combs and a nylon-braided jacket for tidy routing in compact cases

  • Protects GPU panel from cable contact with 90 degree right angled connector
  • Supports RTX 3090 4070 4080 4090 5070 5080 5090 via 12VHPWR 12V-2x6 interface
  • Enables tidy routing in compact cases using flexible nylon braided jacket and movable zinc alloy combs
  • Delivers up to 600W power through 16AWG tinned copper wires and H++ connector
  • Reduces strain on power cable from panel with 90 degree design preventing excessive bending

12VHPWR Type A Extension Cable

This 90-degree 12V-2x6 extension cable connects a power supply to graphics cards with the small four-pin section above the twelve-pin block. It supports up to 600W through 16AWG tinned copper conductors and is rated for PCIe 5.0 and 5.1 signalling. The Type A orientation matches RTX 3090 Ti, 4070, 4080, 4090, 5070, 5080 and 5090 reference layouts.

Builders with tight side-panel clearance

The right-angled plug keeps the cable flush against the card so the side panel closes without crushing the wires. Three movable zinc-alloy combs and a nylon-braided jacket let you route the tail cleanly in compact chassis. Buyers whose GPU places the four-pin section below the twelve-pin block need the Type B variant instead.

Movable combs and braided sleeve

The three sliding combs bundle the individual wires into a single flat ribbon that stays where you position it. The flexible nylon braid resists kinking during installation and reduces visible clutter for better internal airflow. No software or additional adapters are included in the package.

Highlights

  • Protects GPU panel from cable contact with 90 degree right angled connector
  • Supports RTX 3090 4070 4080 4090 5070 5080 5090 via 12VHPWR 12V-2x6 interface
  • Enables tidy routing in compact cases using flexible nylon braided jacket and movable zinc alloy combs
  • Delivers up to 600W power through 16AWG tinned copper wires and H++ connector
  • Reduces strain on power cable from panel with 90 degree design preventing excessive bending

Specifications

No published specifications for this item yet.

Questions about this item

What GPU connector layout must my graphics card have for this Type A extension to fit?

The card needs a 12VHPWR or 12V-2x6 socket where the small 4-pin block sits above the 12-pin block.

Will the 90-degree plug clear the side panel on a compact case that already has a straight 12VHPWR cable from the power supply?

Yes, the right-angled male end points the cable away from the panel so the existing PSU cable does not press against the glass.

How can I confirm the extension is delivering the full 600 W after I route it behind the motherboard tray?

Under GPU load the 16 AWG tinned copper conductors and H++ connector should stay cool to the touch and the card should not throttle.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.