We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Small steel beam clip with zinc plated black finish and rotating conduit hanger

B-LINE

B-LINE BG-8-12-U-2-4 Beam Clip Coupling 12 75 360

SKU CH-REPR-6NW0X

Beam clip coupling secures 1/2 in and 3/4 in conduit or pipe to 1/8 in to 1/4 in flanges with 75 lb load capacity and 360 degree rotation

  • Secures conduit to beams with hammer-on installation
  • Supports 1/2 in and 3/4 in EMT and RMC conduit
  • Rotates 360 degrees for flexible positioning
  • Zinc-plated steel resists corrosion in harsh environments
  • Rated for 75 lb load capacity on 1/8 in to 1/4 in flanges

Beam Clip for 1/2 in and 3/4 in Conduit

The Eaton B-Line BG-8-12-U-2-4 beam clip secures EMT and RMC conduit to horizontal beams with flange thickness between 1/8 in and 1/4 in. Its hammer-on mounting allows fast installation without drilling or welding. The zinc-plated steel body resists corrosion in indoor and covered outdoor environments. It suits electrical contractors and maintenance crews running conduit along structural steel.

75 lb Load Capacity Under Static Load

The clip is rated for a 75 lb load capacity when mounted on a suitable beam flange. This figure represents the sustained static weight the hanger can support without permanent deformation. Dynamic shock or vibration from equipment startup may reduce the effective margin, so the installer should verify the total suspended weight stays within the rated limit. The 360-degree rotation does not alter the vertical load rating.

360-Degree Rotation for Alignment Flexibility

The hanger rotates a full 360 degrees, letting the conduit run parallel or perpendicular to the beam as routing requires. Rotation is free by hand before the conduit is seated, then locks in position once the pipe is snapped into the clip. No tools are needed to adjust the angle, but the clip cannot compensate for beam flange thicknesses outside the 1/8 in to 1/4 in range.

Highlights

  • Secures conduit to beams with hammer-on installation
  • Supports 1/2 in and 3/4 in EMT and RMC conduit
  • Rotates 360 degrees for flexible positioning
  • Zinc-plated steel resists corrosion in harsh environments
  • Rated for 75 lb load capacity on 1/8 in to 1/4 in flanges

Specifications

BrandEATON B-LINE

Questions about this item

Does the BG-8-12-U-2-4 beam clip generate any noise, heat or draw power when it is installed and loaded all day?

No, the clip is a passive steel fitting with no moving parts, so it produces no noise, no heat and consumes no power.

What must I already have on site for the BG-8-12-U-2-4 to work as intended?

You need a structural beam with a flange thickness between 1/8 in and 1/4 in, plus EMT or RMC conduit sized at 1/2 in or 3/4 in that you intend to support.

Will the 360-degree rotation of the BG-8-12-U-2-4 interfere with older conduit runs that are already fixed in place?

The clip rotates freely through 360 degrees, so you can orient it to clear existing conduit without moving the older runs.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.