We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
White over-ear headphones with padded earcups and adjustable headband

Audio-Technica ATH-M20XWH White Over-Ear Headphones 40mm 47Ω

SKU CH-SAVK-ZD4HE

White over-ear studio headphones with 40 mm drivers, 47 Ω impedance and 96 dB sensitivity for tracking and monitoring

  • TypeOn-Ear
  • ColorWhite
  • THDOn Ear
  • Input Impedance47 ohms
  • Signal to Noise Ratio(SNR)96 decibels
  • Sensitivity96 decibels
  • 40 mm drivers deliver detailed audio across 15–20 000 Hz
  • 47 Ω impedance suits studio gear and portable devices alike
  • 96 dB sensitivity provides loud, clean output from low-power sources
  • Circumaural design isolates sound for focused monitoring in noisy spaces
  • 190 g lightweight build ensures comfort during extended tracking sessions

Professional Studio Monitor Headphones

The Audio-Technica ATH-M20XWH is a white, wired, over-ear headphone designed for studio tracking and monitoring. It uses 40 mm dynamic drivers with neodymium magnets and copper-clad aluminum wire voice coils. The closed-back, circumaural build provides sound isolation for critical listening. A single-side 3.0 m cable ends in a 3.5 mm connector.

Suited for entry-level tracking and monitoring

These headphones fit users who need accurate low-frequency response and isolation for recording or mixing in loud spaces. The lightweight 190 g frame supports extended wear without fatigue. Buyers who need active noise cancellation, a detachable cable, or wireless freedom should look at something else.

47 ohm impedance matches portable and studio gear

At 47 ohms and 96 dB sensitivity, the ATH-M20XWH reaches usable volume from phone outputs, audio interfaces, or desktop headphone amps without extra power. This single spec decides if it works with your source.

Highlights

  • 40 mm drivers deliver detailed audio across 15–20 000 Hz
  • 47 Ω impedance suits studio gear and portable devices alike
  • 96 dB sensitivity provides loud, clean output from low-power sources
  • Circumaural design isolates sound for focused monitoring in noisy spaces
  • 190 g lightweight build ensures comfort during extended tracking sessions

Specifications

BrandAudio-Technica
ModelATH-M20XWH
Part NumberATH-M20XWH
TypeOn-Ear
ColorWhite
THDOn Ear
Input Impedance47 ohms
Signal to Noise Ratio(SNR)96 decibels
Sensitivity96 decibels
Connector3.5mm
Ear Couplingover_ear
Weight261 grams
Noise Cancellingsound_isolation
Microphone Impedance47 ohm
Microphone Signal to Noise Ratio(SNR)96 decibels
Microphone Sensitivity96 decibels
Featuressound_isolation, Detachable, remote, Wired, On Ear, dynamic_driver, 47 ohm

Questions about this item

Should I choose the white ATH-M20XWH or another colour variant for studio tracking?

The white ATH-M20XWH uses the same 40 mm neodymium drivers, 47 Ω impedance and 96 dB sensitivity as other finishes, so tonal balance and isolation are identical; pick the colour you prefer.

What does the 96 dB sensitivity figure mean when I plug these into my audio interface?

At 96 dB sensitivity and 47 Ω impedance, the headphones reach loud monitoring levels from standard interface headphone outputs without needing a dedicated amplifier.

Does the 3.5 mm connector limit the maximum input power of 700 mW in practice?

The 3.5 mm plug carries the full signal; the 700 mW rating at 1 kHz is a driver limit, not a connector limit, so the cable does not cap the power the headphones can handle.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.