We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Metallic SFP+ transceiver module with RJ45 connector, compact silver finish

ARENTI

ARENTI 10GBASE-T SFP+ RJ45 Copper Transceiver Module 80m Cat6a/7 2 in 1 accessory

SKU CH-R1XT-719ZZ

Connects 10 GbE switches via RJ45 up to 80 m on Cat6a/7, hot-pluggable with a 2.5 W metal enclosure

  • 10 Gbps over Cat6a or Cat7 up to 80 m
  • Hot-pluggable SFP+ MSA form factor for instant upgrades
  • Metallic enclosure keeps EMI low for clean signals
  • Operates reliably from 0 °C to 70 °C
  • Maximum draw only 2.5 W for efficient operation

10GBASE-T SFP+ RJ45 Copper Transceiver Module 80m

The ARENTI 10GBASE-T SFP+ RJ45 Copper Transceiver Module delivers 10G bandwidth over Cat6a or Cat7 copper cabling up to 80 metres. It uses a hot-pluggable SFP+ MSA form factor with a compact RJ45 connector and a fully metallic enclosure for low EMI. Maximum power draw is 2.5W and it operates from 0 to 70C (32 to 158F). It complies with IEEE 802.3an and IEEE 802.3az standards and is ROHS compliant.

Network administrators upgrading switches

This module suits administrators who need 10GBASE-T connectivity on SFP+ ports in commercial temperature environments and require compatibility with specific Fortinet FN-TRAN-SFP+GC and FS-TRAN-SFP+GC coded equipment. It is not for buyers who need fibre optic SFP+ transceivers, longer reach than 80 metres over copper, or industrial temperature ranges beyond 70C.

Pre-coded EEPROM for Fortinet compatibility

The bundled EEPROM coding matches Fortinet FN-TRAN-SFP+GC and FS-TRAN-SFP+GC identifiers so the module is recognised immediately by targeted switches without manual configuration. This removes the need for separate coding tools or third-party programming services and reduces deployment time in compatible environments. The 2-wire serial bus provides access to the physical layer IC for diagnostics.

Highlights

  • 10 Gbps over Cat6a or Cat7 up to 80 m
  • Hot-pluggable SFP+ MSA form factor for instant upgrades
  • Metallic enclosure keeps EMI low for clean signals
  • Operates reliably from 0 °C to 70 °C
  • Maximum draw only 2.5 W for efficient operation

Specifications

No published specifications for this item yet.

Questions about this item

Does my switch need an SFP+ cage that supports 10GBASE-T and the 2.5W power budget?

Yes, the module plugs into a standard SFP+ MSA slot and draws up to 2.5W, so the host port must supply that power and accept 10GBASE-T RJ45 transceivers.

Will the 80m Cat6a/7 link still come up if I connect to a legacy 1G copper port?

The transceiver is IEEE 802.3an and 802.3az compliant and presents a standard RJ45 interface, so it will negotiate the highest speed both ends support over the installed cable.

How can I confirm the module is operating correctly after installation?

Check the switch port LEDs for a 10G link light, verify the transceiver temperature stays within the 0 to 70C range via the management interface, and run a 10G throughput test over the Cat6a or Cat7 cable.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.