We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
White 140 mm case fan with transparent rotor and 12 A-RGB LEDs on hub

ARCTIC

ARCTIC P14 PWM PST A-RGB 140 mm White Case Fan

SKU CH-HTVE-2T9AK

A 140 mm white case fan with 12 A-RGB LEDs, PWM control from 200 to 1900 RPM, and 2.00 mm H₂O static pressure for radiators

  • ColorWhite
  • 12 A-RGB LEDs deliver even lighting across the hub and transparent rotor
  • 200–1900 RPM PWM range with 0 RPM below 5 % duty cycle keeps noise minimal
  • 00 mm H₂O static pressure ensures strong airflow through radiators and heatsinks
  • 9 CFM (117.06 m³/h) airflow provides efficient case cooling
  • 4-pin PWM and 3-pin A-RGB connectors with integrated Y-splitters simplify daisy-chaining

140 mm PWM Case Fan

The ARCTIC P14 PWM PST A-RGB is a 140 mm white case fan built for static-pressure cooling. It runs at 200-1900 RPM and can stop completely below five percent PWM duty. Twelve addressable RGB LEDs sit on the hub and transparent rotor for even illumination. A 4-pin PWM connector and a 3-pin 5 V A-RGB header provide control.

Upgrade from lower-pressure fans

This fan replaces standard airflow models when cooling dense fin stacks or radiators. Its 2.00 mm H₂O static pressure and 68.9 CFM airflow handle restrictive layouts without excessive noise. The jump is worthwhile when your current fans stall against a thick heatsink or liquid-cooling radiator. Builders who need pure airflow volume for open meshes will not benefit.

Check motherboard headers and clearance

Verify a 4-pin PWM fan header and a 5 V 3-pin A-RGB header exist on your board or controller. Confirm 140 mm mounting points match your case or radiator. Ensure the semi-passive 0 RPM mode is supported by your fan curve software. Systems lacking a 5 V A-RGB header cannot use the lighting.

Highlights

  • 12 A-RGB LEDs deliver even lighting across the hub and transparent rotor
  • 200–1900 RPM PWM range with 0 RPM below 5 % duty cycle keeps noise minimal
  • 00 mm H₂O static pressure ensures strong airflow through radiators and heatsinks
  • 9 CFM (117.06 m³/h) airflow provides efficient case cooling
  • 4-pin PWM and 3-pin A-RGB connectors with integrated Y-splitters simplify daisy-chaining

Specifications

ColorWhite

Questions about this item

Will the 140 mm frame with 4-pin PWM and 3-pin 5 V A-RGB connectors fit my case fan mounts and motherboard headers?

The fan uses a standard 140 mm square frame, a 4-pin PWM connector for speed control and a 3-pin 5 V A-RGB header for lighting, matching common case mounts and motherboard headers.

How do I daisy-chain several fans using the integrated Y-splitters on both the PWM and A-RGB cables?

Plug the first fan’s PWM and A-RGB leads into the motherboard, then connect each additional fan to the previous fan’s built-in Y-splitter; both power and lighting signals pass through the chain.

The semi-passive mode stops the rotor below 5 % PWM — will the 12 A-RGB LEDs stay lit while the blades are at 0 RPM?

Yes, the 5 V A-RGB circuit is independent from the PWM motor drive, so the 12 hub-mounted LEDs remain fully controllable even when the fan runs at 0 RPM.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.