We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Wet Sounds amplifier wiring kit with 1/0 and 4 AWG power cables, distribution block and ANL fuse holder

Wet Sounds

Wet Sounds Front Battery 2 Amplifier Wiring Kit

SKU CH-E8SC-XCXVX

Amplifier wiring kit for up to two amplifiers mounted near the front battery, with 1/0 AWG and 4 AWG power cables, distribution block and ANL fuse holder

  • TypeAmplifiers
  • 10 ft 1/0 AWG power wire handles high current to front-mounted amps
  • 10 ft 4 AWG secondary power wire feeds additional amplifiers
  • 25 ft remote turn-on wire reaches any amplifier location
  • Big Block distribution block splits power and ground cleanly
  • ANL fuse holder with 300 A and 150 A fuses protects the system

Amplifier Wiring Kit for Two Amps

This Wet Sounds kit supplies power and signal cables for installations with up to two amplifiers. It is designed for setups where the amplifiers sit closer to the front battery rather than the rear of the vehicle. The package includes both 1/0 AWG and 4 AWG power and ground wires plus a remote turn-on lead.

Check Battery Location and Fuse Requirements

Verify that your amplifiers will be mounted near the front battery so the 10-foot power leads reach without splicing. Confirm that your equipment can accept ANL and Mini ANL fuse holders rated at 300A and 150A respectively. Ensure you have space for the included Big Block distribution block near the battery.

Upgrades Factory Wiring for Marine-Grade Reliability

This kit replaces thin factory power cables and basic fuse holders with CEA-2015 and BC-5W2 compliant marine wire. The jump is worth it when you need 100% oxygen-free tinned copper conductors and twisted-pair shielded RCA interconnects for noise-free signal transfer. It also extends the Wet Sounds warranty by one year when used throughout the system.

Highlights

  • 10 ft 1/0 AWG power wire handles high current to front-mounted amps
  • 10 ft 4 AWG secondary power wire feeds additional amplifiers
  • 25 ft remote turn-on wire reaches any amplifier location
  • Big Block distribution block splits power and ground cleanly
  • ANL fuse holder with 300 A and 150 A fuses protects the system

Specifications

TypeAmplifiers

Questions about this item

Does the kit include everything needed to run two amplifiers from the front battery, or must I buy extra cable or fuses?

The box supplies 10 feet of 1/0 AWG power and ground wire, 10 feet of 4 AWG power and ground wire, 25 feet of remote turn-on wire, a Big Block combo distribution block, an ANL battery fuse holder with 300A ANL fuses and 150A Mini ANL fuses — no extra cable or fuses are required for a standard two-amp front-battery install.

When should I choose this Front Battery 2 Amplifier kit instead of the Rear kit?

Choose this kit when the amplifiers are mounted closer to the front battery than they would be to a rear battery; the included 10-foot main power and ground leads are sized for that shorter run, whereas the Rear kit provides longer cable for rear-mounted amps.

What does the 300A ANL fuse rating mean for my system once it is installed?

The 300A ANL fuse protects the main 1/0 AWG power feed from the battery; it will carry the combined current draw of both amplifiers up to 300 amperes before blowing, so the amplifiers’ total fused rating must not exceed that figure.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.