We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Yellow pneumatic orbital sander with three backing plates, assorted sandpapers and foam pads in a kit

VEVOR

VEVOR WFS-1031-YW 15000 RPM 58-Piece Random Orbital Air Sander Kit

SKU CH-NHF5-22GN2

A 15,000 RPM pneumatic random orbital sander with 58 pieces including 36 sandpapers, wool pads and wavy foam pads for curved surfaces

  • TypeOther Appliances
  • Width7.09
  • 15,000 RPM free speed delivers rapid material removal
  • 58-piece kit includes sandpapers, wool pads and wavy foam for every stage
  • Three backing-plate sizes (1/2/3 in) match contoured or flat surfaces
  • 3 CFM at 90 PSI runs on common shop compressors
  • Lightweight 1.8 lb aluminium body reduces fatigue during extended use

15000 RPM Pneumatic Sander Kit

The VEVOR WFS-1031-YW is a compact air-powered random orbital sander built for auto body work and detail finishing. It runs at 15000 RPM with a 1/4" NPT inlet and requires 90 PSI operating pressure. The 58-piece kit includes the sander, three backing plates, sandpapers, wool pads, wavy foam pads, a quick connector and a striking needle.

58-Piece Kit Capacity and Grit Range

The set supplies 36 sandpapers across 80, 120 and 240 grits for material removal through fine finishing. Three sizes of backing plates, wool pads, fibre wool pads, cushioning pads and nine wavy foam pads cover flat and contoured panels. The 3 CFM air consumption demands a compressor that can sustain flow; smaller tanks will run out of air during extended use.

Thermals Noise and Power Draw

The aluminium body weighs 1.8 lbs and measures 6.6 x 3.1 x 1.7 inches, keeping vibration low during one-hand operation. No motor heat is generated because the tool runs on compressed air, so surface temperature stays near ambient. Noise level is governed by the compressor and exhaust; the sander itself has no electric motor whine.

Highlights

  • 15,000 RPM free speed delivers rapid material removal
  • 58-piece kit includes sandpapers, wool pads and wavy foam for every stage
  • Three backing-plate sizes (1/2/3 in) match contoured or flat surfaces
  • 3 CFM at 90 PSI runs on common shop compressors
  • Lightweight 1.8 lb aluminium body reduces fatigue during extended use

Specifications

TypeOther Appliances
Width7.09

Questions about this item

Will the 1/4" NPT air inlet and 90 PSI requirement work with my existing compressor setup?

The sander needs a 1/4" NPT connection and runs at 90 PSI with 3 CFM consumption, so check your compressor delivers that flow at pressure.

How can I confirm the sander is running at the rated 15000 RPM after I hook it up?

Listen for smooth, steady operation without excessive vibration; the motor should sound consistent at full throttle when the trigger is held.

Which pads and sandpapers come in the 58-piece kit and what must I supply myself?

The box includes the sander, three backing plates (1/2/3 inch), 36 sandpapers (80/120/240 grit), three woolen pads, three fiber woolen pads, nine wavy foam pads, three cushioning pads, a quick air hose connector and a striking needle — you only need to provide compressed air.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.