We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Rectangular gold heat exchanger with dense aluminum fins and copper tubes, 16 by 16 inch core, 193 fins visible

VEVOR

VEVOR C16 specialty appliance 16x16 in 193 fins 80K BTU

SKU CH-V587-GDPB8 MPN C16

A 16 x 16 inch water-to-air heat exchanger with 193 aluminium fins and three rows of 3/8 inch copper tubes, delivering up to 160k BTU per hour for outdoor wood furnaces and forced-air heating

  • TypeOther Appliances
  • Width18.5
  • Up to 160kBtu output from 12 fins per inch across 3 copper tube rows
  • 193 epoxy-coated aluminum fins resist corrosion and reduce internal scaling for lasting performance
  • 16 x 16 inch plate area provides large surface for effective heat transfer
  • Copper-brazed edges and contact points create a leak-resistant unit for high pressure and temperature
  • Operates from -40°C to 180°C covering outdoor wood furnaces and forced-air heating

Core Specifications

The VEVOR C16 specialty appliance is a copper-brazed heat exchanger built for outdoor wood furnaces and forced-air heating systems. Its 16 by 16 inch plate area and 193 epoxy-coated aluminum fins serve installers who need a compact, high-surface-area core for hydronic-to-air heat transfer. The unit weighs 13.65 lb and fits within a 21.57 by 16.06 by 3.62 inch envelope.

Thermals and Pressure

Rated for 80K BTU with a peak capacity of 160kBtu per hour, the exchanger uses three rows of 3/8 inch seamless copper tubes and twelve fins per inch to move heat between fluid and air streams. It operates from minus 40 to 180 degrees Celsius and withstands a maximum working pressure of 2.5 MPa, making it suitable for high-temperature hydronic loops without leaks.

Upgrade Context

This model replaces smaller or single-row cores where the 16 by 16 inch footprint is available but greater fin count and copper tube rows are needed for higher output. The jump is worthwhile when the existing exchanger cannot meet the 80K BTU design load or when corrosion has degraded fin efficiency in an outdoor furnace installation.

Highlights

  • Up to 160kBtu output from 12 fins per inch across 3 copper tube rows
  • 193 epoxy-coated aluminum fins resist corrosion and reduce internal scaling for lasting performance
  • 16 x 16 inch plate area provides large surface for effective heat transfer
  • Copper-brazed edges and contact points create a leak-resistant unit for high pressure and temperature
  • Operates from -40°C to 180°C covering outdoor wood furnaces and forced-air heating

Specifications

TypeOther Appliances
Width18.5

Questions about this item

How do I mount the 16 x 16 inch plate into my forced-air plenum without blocking the 193 fins?

Slide the 21.57 x 16.06 inch frame into the duct opening so the 3.62 inch depth sits flush, then seal the perimeter with foil tape; the 12 fins per inch spacing stays clear because the copper ports protrude only on the header side.

What part of the C16 will need attention first after several heating seasons?

The epoxy coating on the aluminum fins resists scaling, but mineral deposits can still narrow the 3/8 inch copper tubes; flushing the loop annually keeps the 2.5 MPa pressure rating intact.

At what point does the 80K BTU rating become the bottleneck during a long burn?

When the supply water exceeds 180 °C or the air flow cannot pull 160 kBtu per hour across the 193 fins, the exchanger hits its thermal limit before the copper structure does.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.