We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
VEVOR ALK-T8 fiber fusion splicer in a rugged case with 5-inch touch screen and accessories

VEVOR

VEVOR ALK-T8 Fiber Fusion Splicer 6 Motors 5" Touch Screen 7800mAh Battery

SKU CH-H349-02BQ1

A core-alignment fiber fusion splicer with six motors, 6-second splicing, 13-second heating, a 5-inch touch screen and a 7800 mAh battery

  • Device TypeOther Appliances
  • 6-second splicing with 0.01 dB loss via 6-motor core alignment
  • 5-inch touch screen shows 320x single-axis or 200x dual-axis views
  • 7800 mAh battery supports extended field splicing sessions
  • 3-in-1 fiber holder handles SM, MM, DS, NZDS, pigtail and patch cables
  • Built-in VFL and OPM measure loss and verify continuity

Core-alignment splicing with six motors

This fusion splicer uses six high-precision motors to perform core and cladding alignment on single-mode, multimode, DS and NZDS fibers. It is built for field technicians and contractors who need reliable joint preparation and low-loss fusion in telecom, datacom or enterprise installations. The kit includes a cleaver, stripper, miller pliers, cleaning supplies and a portable case for complete on-site readiness.

7800 mAh battery and 3-in-1 holder capacity

The 7800 mAh battery supports extended outdoor sessions without mains power, while the 3-in-1 holder accommodates bare fiber, pigtails and patch cables up to 3 mm. Splicing completes in 9 seconds fast mode or 13 seconds standard mode, with heating also at 13 seconds. Fusion loss reaches as low as 0.01 dB for multimode fiber, though very high fiber-count ribbon work or angled-polish connectors fall outside the holder design.

5-inch touch screen and 11.8 lb field weight

A 5-inch color touch screen provides independent 320x X or Y views or simultaneous 200x X and Y monitoring for clear core visibility during alignment. The unit weighs 11.8 lb and measures 7.9 x 5.7 x 5 inches, so it remains portable in its case but is not a lightweight handheld tool. Built-in VFL and OPM functions add link verification without extra instruments, and the cooling tray protects the heater between cycles.

Highlights

  • 6-second splicing with 0.01 dB loss via 6-motor core alignment
  • 5-inch touch screen shows 320x single-axis or 200x dual-axis views
  • 7800 mAh battery supports extended field splicing sessions
  • 3-in-1 fiber holder handles SM, MM, DS, NZDS, pigtail and patch cables
  • Built-in VFL and OPM measure loss and verify continuity

Specifications

Device TypeOther Appliances

Questions about this item

Will the ALK-T8's 3-in-1 fiber holder work with the bare fiber and patch cables I already use?

Yes, the 3-in-1 holder accepts SM, MM, DS, NZDS, pigtail, bare fiber and patch cable without extra adapters.

How can I confirm the splicer is performing within the 0.01 dB loss spec after setup?

Run a test splice on the 5-inch touch screen; the real-time X/Y 200x view and built-in OPM let you verify loss readings immediately.

Do I need to buy a cleaver, stripper or heat-shrink tubes separately, or are they included?

The box includes a fiber cleaver, stripper, 3-hole Miller pliers, 100 heat-shrink tubes, 2 spare electrodes plus cleaning tools and a portable case.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.