We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
VEVOR 1/2HP furnace blower motor with capacitor and 11-inch hold hoop

VEVOR

VEVOR 1/2HP Furnace Blower Motor 208/230V 1075RPM 5-Speed 48 Frame 3.4" Shaft 7.5F Capacitor 11" Hoop

SKU CH-FSYS-XA76C

Half-horsepower furnace blower motor runs at 1075 RPM with five speeds on 208/230 V, includes 7.5 µF capacitor and 11-inch hold hoop

  • TypeOther Appliances
  • Width8.27
  • 1/2 HP motor powers residential furnaces and air handlers
  • 208/230 V supply with 2.7 A draw fits standard HVAC wiring
  • Five selectable speeds at 1075 RPM match airflow to demand
  • 48 frame with 3.4" shaft and 0.5" diameter ensures direct-drive fit
  • Includes 7.5 µF 450 V capacitor and 11" hold hoop for immediate installation

1/2 HP Furnace Blower Motor for Residential HVAC

This 1/2 HP furnace blower motor runs at 1075 RPM with five selectable speeds on a 208/230 V, 60 Hz supply. It fits 48-frame direct-drive applications in residential and light-commercial indoor furnaces, air handlers and packaged units. The package includes a 7.5F/450 V capacitor, an 11-inch hold hoop and an instruction manual.

Thermals Noise and Power Draw

The motor draws a rated 2.7 A at full load and is designed for strong performance while maintaining low noise levels during normal operation. CW/CCW rotation is reversible to suit the installation. No additional thermal or acoustic specifications are provided by the supplier.

Matching Nameplate Specifications Is Essential

Buyers must verify that the horsepower, voltage, frame size, shaft diameter and shaft length on their existing motor’s nameplate match this unit exactly. Installing a lower horsepower motor can cause overheating and improper function, so precise specification matching is the single factor that decides fitment.

Highlights

  • 1/2 HP motor powers residential furnaces and air handlers
  • 208/230 V supply with 2.7 A draw fits standard HVAC wiring
  • Five selectable speeds at 1075 RPM match airflow to demand
  • 48 frame with 3.4" shaft and 0.5" diameter ensures direct-drive fit
  • Includes 7.5 µF 450 V capacitor and 11" hold hoop for immediate installation

Specifications

TypeOther Appliances
Width8.27

Questions about this item

How do I wire this 1/2HP furnace blower motor for 208/230V and set the correct rotation direction?

Connect the 208-230V supply to the motor terminals, install the included 7.5F/450V capacitor per the wiring diagram, and select CW or CCW rotation by swapping the appropriate leads as shown in the manual. The 5-speed taps let you choose airflow; verify the nameplate horsepower and amperage match your furnace before powering up.

What maintenance will the included 7.5F/450V capacitor and the motor bearings need over time?

The 7.5F/450V capacitor is a wear item; plan to replace it if the motor hums, starts slowly, or draws higher than the 2.7A rated current. Keep the motor vents clear of dust and lubricate the sleeve bearings annually with a few drops of lightweight electric-motor oil to maintain low-noise operation at 1075 RPM.

At what point will the 2.7A full-load current limit trigger the furnace safety shutdown during a long heating cycle?

If airflow is restricted — dirty filter, closed dampers, or undersized ductwork — the motor will pull more than its 2.7A rated current at 208-230V, causing the internal thermal protector to trip and shut the blower down until it cools.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.