We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Square flat panel antenna with two RPSMA pigtail leads

Ventev

Ventev M6060060P3D20 2.4/5GHz 6dBi Panel Antenna 2 RPSMA

SKU CH-AN59-HRFBC

Dual-band directional panel antenna with 6 dBi gain, 40° beamwidth and two RPSMA connectors for indoor or outdoor Wi-Fi

  • Dual-band coverage for 2.4 GHz and 5 GHz networks
  • 6 dBi gain extends wireless reach in targeted directions
  • 40° beamwidth focuses signal for point-to-point links
  • Two RPSMA connectors enable MIMO or diversity configurations
  • 90 cm pigtails allow flexible placement near access points

Ventev 6 dBi Dual-Band Panel Antenna

The Ventev M6060060P3D20 is a directional panel antenna built for indoor or outdoor Wi-Fi deployments. It covers 2.4 GHz to 2.5 GHz and 5.15 GHz to 5.85 GHz with 6 dBi gain and a 40° horizontal and vertical beamwidth. Two 90-inch pigtail leads end in RPSMA plug connectors for direct attachment to compatible access points or radios. Its low-profile housing measures 10.3 by 10.3 by 1.4 inches and weighs 1.05 lbs.

Sustained RF Performance

The 6 dBi gain provides consistent signal focus across both supported bands, maintaining the stated 40° beamwidth during continuous operation. Dual-band coverage allows the same antenna to serve 2.4 GHz and 5 GHz clients without swapping hardware. The fixed radiation pattern suits point-to-point or sector coverage where predictable lobe shape matters more than peak burst throughput. No active cooling or power draw is involved, so thermal throttling does not apply.

Installation Notes

Mast mounting is the intended method; the package includes Gimbal Clamp kits for that purpose. The two RPSMA pigtails are 90 inches long, so routing distance to the radio is fixed unless you add approved extensions. Installers must align the panel within the 40° beamwidth for the target area; misalignment is the most common cause of weak links. The antenna is rated for indoor and outdoor use, but the supplied clamps are designed for standard mast diameters only.

Highlights

  • Dual-band coverage for 2.4 GHz and 5 GHz networks
  • 6 dBi gain extends wireless reach in targeted directions
  • 40° beamwidth focuses signal for point-to-point links
  • Two RPSMA connectors enable MIMO or diversity configurations
  • 90 cm pigtails allow flexible placement near access points

Specifications

BrandVentev

Questions about this item

Does the 6 dBi panel antenna generate any noise or heat when running continuously?

The antenna is a passive component with no electronics, so it produces no noise, no heat and draws no power.

What equipment must I already have to use the two RPSMA connectors?

You need a wireless access point or radio that has two RPSMA jack ports and operates in the 2.4 GHz to 2.5 GHz or 5.15 GHz to 5.85 GHz bands.

Will the 40° horizontal beamwidth work with older 2.4 GHz access points I want to keep?

Yes, the antenna covers the 2.4 GHz to 2.5 GHz range, so legacy 2.4 GHz radios can connect through the same RPSMA leads.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.