OneOdio Pro-10 Over-Ear Headphones 50mm Drivers 32 ohm 3.5mm 6.35mm Jack Red
Wired over-ear headphones with 50 mm drivers, 32 ohm impedance, and detachable 3.5 mm and 6.35 mm jacks for studio monitoring and DJ use
- TypeOn-Ear
- ColorWhite
- Frequency Response5Hz-16KHz
- Input Impedance80 ohms
- Power Supplyfalse
- Connector3.5mm
- 50 mm neodymium drivers deliver deep bass for mixing and monitoring
- Detachable 3.5 mm and 6.35 mm plugs remove the need for an adapter
- 90 ° swivelling ear cups enable single-side monitoring during sessions
- Adjustable headband with soft padded cushions provides comfort for extended use
- 8 ft cable gives freedom of movement around equipment
Studio DJ headphones with dual jacks
The OneOdio Pro-10 is a wired over-ear headphone built for studio monitoring, DJ mixing, recording and podcasting. Large 50 mm neodymium drivers deliver dynamic bass response. The 32 ohm impedance suits portable devices and professional gear alike. Red finish distinguishes this model in a busy booth.
Detachable cables and swivel cups
Two detachable cables terminate in 3.5 mm and 6.35 mm plugs so no adapter is needed. The 9.8-foot cord reaches across a control room. Ear cups swivel 90° for single-ear monitoring. Padded cushions and an adjustable headband aim for fatigue-free sessions. Passive isolation blocks ambient noise.
Check your source jack and impedance match
Verify that your mixer, interface, laptop or instrument provides a 3.5 mm or 6.35 mm output. The 32 ohm load is easy to drive but confirm your gear can supply adequate voltage for the desired volume. No microphone is included; a separate mic is required for voice work.
Highlights
- 50 mm neodymium drivers deliver deep bass for mixing and monitoring
- Detachable 3.5 mm and 6.35 mm plugs remove the need for an adapter
- 90 ° swivelling ear cups enable single-side monitoring during sessions
- Adjustable headband with soft padded cushions provides comfort for extended use
- 8 ft cable gives freedom of movement around equipment
Specifications
| Brand | PHILIPS |
|---|---|
| Series | Classic Series |
| Model | WFL900/H |
| Part Number | Pro-red |
| Type | On-Ear |
| Color | White |
| Frequency Response | 5Hz-16KHz |
| Input Impedance | 80 ohms |
| Power Supply | false |
| Connector | 3.5mm |
| Ear Coupling | Earbud |
| Noise Cancelling | Passive |
| Microphone Signal to Noise Ratio(SNR) | 110 decibels |
| Microphone Sensitivity | 110 decibels |
| Compatibility | Universal |
| Features | sound_isolation, Retractable, Media Control, voice, Wired, Over Ear, dynamic_driver, 32 ohm, Headphone |
| Windows Vista | Certified for Windows Vista |
| Package Contents | Headphone, Ear Cushions, Cable |
Questions about this item
How can I confirm the 50 mm neodymium drivers are producing the advertised 5 Hz – 16 kHz frequency response after setup?
Play a frequency-sweep test tone from 5 Hz to 16 kHz through the 3.5 mm or 6.35 mm plug and listen for even output across the range; the 32 ohm impedance and 110 dB microphone SNR figures indicate the drivers are performing to spec.
What comes in the box and which cables or adapters must I purchase separately?
The package includes the headphones, ear cushions and a detachable 9.8-foot cable with both 3.5 mm and 6.35 mm plugs; no extra adapters are required for devices with either jack size.
Should I choose the 32 ohm or 80 ohm version for studio monitoring with a 6.35 mm interface?
The Pro-10 is a 32 ohm model optimised for universal 3.5 mm and 6.35 mm jacks; the 80 ohm figure belongs to a different Philips reference and is not an option for this headphone.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
HQRP 2-Pack 10 ft 2.1mm x 5.5mm DC Power Extension Cable + Coaster
- Black



