We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Small green circuit board with a 20-pin male connector on one edge and two USB Type-A female sockets

Manw

Manw USB3.1 Type-E 20Pin Male to Dual USB2.0 A Female + 9Pin/10Pin Header Internal Hub Adapter

SKU CH-DGM6-2NCGQ

Converts a motherboard USB 3.1 Type-E 20-pin header into two USB 2.0 Type-A ports plus a 9/10-pin header at 480 Mbps with 500 mA per port

  • Converts Type-E 20Pin header to two USB 2.0 Type-A ports and a 9/10Pin header
  • Built-in hub controller delivers stable 480Mbps data across both USB 2.0 ports
  • Each USB 2.0 port supplies 500mA at 5V for internal peripherals
  • Works with both 9Pin and 10Pin motherboard USB 2.0 headers for broad compatibility
  • Compact PCB with adhesive backing enables tidy internal mounting in ATX, MATX or ITX builds

Internal USB Expansion

This adapter converts a motherboard front-panel USB 3.1 Type-E 20-pin male header into two USB 2.0 Type-A female ports and a 9/10-pin USB 2.0 header. A built-in hub controller provides stable 480 Mbps data speed on each port. Each output delivers 500 mA at 5 V for peripherals such as RGB controllers, Wi-Fi adapters or internal card readers. It suits DIY builders and embedded-system refits needing extra internal USB connections.

Header Compatibility Check

Verify that your motherboard provides a USB 3.1 Type-E (Key-A 20-pin) front-panel header before ordering. The adapter also requires a free 9-pin or 10-pin USB 2.0 internal header on the board for the third output. Confirm the pin-out matches the standard 9/10-pin layout used by your chassis front I/O module. No additional drivers are needed for operation.

Build And Daily Use

A compact PCB with adhesive backing secures the unit inside the case for tidy hidden wiring. The dual 9/10-pin compatibility solves header mismatches between newer Type-E front panels and legacy motherboard USB headers. Plug-and-play operation works across ATX, mATX and ITX form factors. The splitter expands limited internal USB resources for front-panel modules, fan hubs and lighting controllers.

Highlights

  • Converts Type-E 20Pin header to two USB 2.0 Type-A ports and a 9/10Pin header
  • Built-in hub controller delivers stable 480Mbps data across both USB 2.0 ports
  • Each USB 2.0 port supplies 500mA at 5V for internal peripherals
  • Works with both 9Pin and 10Pin motherboard USB 2.0 headers for broad compatibility
  • Compact PCB with adhesive backing enables tidy internal mounting in ATX, MATX or ITX builds

Specifications

BrandManw

Questions about this item

Does the package include any extra cables or mounting hardware, or is it just the adapter board?

Only the adapter board is supplied; it has an adhesive backing for securing it inside the case, so no separate screws or cables are needed.

Should I pick a different model if my motherboard has only the older 9-pin USB 2.0 header instead of the 10-pin version?

No, this single adapter fits both the 9-pin and 10-pin internal USB 2.0 headers, so it works with either layout.

What real-world transfer speed can I expect when I plug a USB 2.0 flash drive into one of the Type-A ports?

The built-in hub controller delivers the standard USB 2.0 rate of 480 Mbps, so sustained reads and writes will sit at that ceiling.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.