We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black push-fit tee fitting pack of ten with threaded branch

Legris

Legris 3108 62 18 Male Branch Tee 1/2 in OD 290 PSI Pack of 10

SKU CH-V4SJ-2E52X MPN 3108

Push-fit male branch tee connects two 1/2 in tubes to a 3/8 in MNPT thread at 290 PSI, supplied as a pack of 10

  • TypeDrain Components
  • MaterialHAWA
  • ColorBlack
  • Push-to-connect design enables tool-free installation on 1/2 in tubing
  • Male NPT branch with pre-applied sealant speeds up threaded connections
  • Rated for 290 PSI to handle demanding air and fluid lines
  • Fiberglass-reinforced nylon body resists corrosion and cutting fluids
  • Pack of 10 fittings supports multiple assembly points

Push-Fit Tee for Pneumatic Lines

The Legris 3108 62 18 is a male branch tee that joins two 1/2 in push-to-connect tubes to a 3/8 in male NPT port. Its fiberglass-reinforced nylon body handles air, cutting fluids and inert gases up to 290 PSI. Pre-applied thread sealant on the NPT end speeds installation without extra tape or compound. Supplied in a pack of ten for production or maintenance use.

Suits Quick-Connect Air Systems

This fitting suits technicians building or repairing push-fit pneumatic circuits that need a 3/8 in threaded branch. It does not suit systems that require compression or flare connections, metal-bodied fittings for higher temperatures, or any tube size other than 1/2 in OD on the push-to-connect ends.

1/2 in Push-to-Connect with 3/8 in MNPT Branch

The critical specification is the combination of dual 1/2 in push-to-connect ports and a single 3/8 in male NPT port with pre-applied sealant. If your circuit uses different tube diameters, thread sizes or connection styles, this tee will not fit.

Highlights

  • Push-to-connect design enables tool-free installation on 1/2 in tubing
  • Male NPT branch with pre-applied sealant speeds up threaded connections
  • Rated for 290 PSI to handle demanding air and fluid lines
  • Fiberglass-reinforced nylon body resists corrosion and cutting fluids
  • Pack of 10 fittings supports multiple assembly points

Specifications

TypeDrain Components
MaterialHAWA
ColorBlack
BrandLegris
Model3108 62 18

Questions about this item

What comes in the pack and what else do I need to connect 1/2 in OD tubing?

The pack contains ten 3108 62 18 male branch tees. Each tee has push-to-connect ends for 1/2 in OD tube on sides A and B and a 3/8 in MNPT thread on side C with pre-applied sealant. You only need the 1/2 in OD tubing; no separate ferrules or clamps are required.

How do I choose between the listed versions for my air line?

The product is offered as a single configuration: 1/2 in OD push-to-connect on both run ports and a 3/8 in male NPT branch with 290 PSI rating. Select this version when your tubing is 1/2 in OD and the branch must thread into a 3/8 in female NPT port.

What does the 290 PSI rating mean once the tee is installed in my compressed-air system?

It is the maximum working pressure the fiberglass-reinforced nylon body and push-to-connect seals are designed to hold at room temperature. In a real machine, keep the system pressure at or below 290 PSI and verify the tubing used also meets or exceeds that pressure.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.