We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black push-fit tee fitting with three 1/8 in connections and male thread

Legris

Legris 3108 53 11 Male Branch Tee 1/8 in OD 290 PSI PK10 trap

SKU CH-CH4F-06PY6 MPN 3108

A pack of ten push-fit male branch tees connects 1/8-inch tubing on two sides to a 1/8-inch male NPT thread on the third, rated to 290 PSI for air, cutting fluids and inert gases

  • TypeDrain Components
  • MaterialHAWA
  • ColorBlack
  • Push-to-connect design speeds installation without tools
  • Three 1/8 in ports handle air, cutting fluids and inert gases
  • Pre-applied thread sealant on the MNPT end prevents leaks
  • Fibre-reinforced nylon body withstands 290 PSI working pressure
  • Pack of 10 fittings covers multiple connection points

Push-fit tee for pneumatic systems

This push-fit branch tee connects two 1/8-inch outer-diameter tubes to a male NPT thread of the same size. The fiberglass-reinforced nylon body handles air, cutting fluids and inert gases up to 290 PSI. Pre-applied thread sealant on the NPT end speeds assembly without extra tape or paste. Supplied in a pack of ten fittings.

Maintenance teams and OEM assemblers

Suited for technicians who need quick, tool-free connections on low-pressure pneumatic circuits. The push-to-connect ends release with a simple collet press, reducing downtime during line changes. Not intended for installers who require compression or flare fittings, nor for systems operating above the rated pressure.

1/8-inch tube and thread combination

The fitting joins two 1/8-inch OD tubes to a 1/8-inch male NPT port in a single branched junction. This exact size match determines whether the tee fits the existing ports and tubing in the circuit. Verify the tube OD and thread specification before ordering.

Highlights

  • Push-to-connect design speeds installation without tools
  • Three 1/8 in ports handle air, cutting fluids and inert gases
  • Pre-applied thread sealant on the MNPT end prevents leaks
  • Fibre-reinforced nylon body withstands 290 PSI working pressure
  • Pack of 10 fittings covers multiple connection points

Specifications

TypeDrain Components
MaterialHAWA
ColorBlack
BrandLegris
Model3108 53 11

Questions about this item

Does the pack of 10 male branch tees include any tubing or thread-seal tape, or must those be purchased separately?

The pack contains only the ten push-fit tee fittings with pre-applied thread sealant on the 1/8 in MNPT branch; 1/8 in OD tubing and any additional seal tape are not included.

The listing shows model 3108 53 11 — are there other capacities or versions of this fitting I should consider?

Model 3108 53 11 is a single configuration: 1/8 in OD push-to-connect on both run ports, 1/8 in MNPT on the branch, rated 290 PSI, supplied in a pack of 10; no alternate capacities or versions are offered under this part number.

In a working airline, what does the 290 PSI rating actually mean for this tee?

It is the maximum working pressure the fiberglass-reinforced nylon body and push-to-connect seals are designed to hold at room temperature with air, cutting fluids or inert gases; system pressure should stay at or below this figure.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.