We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black push-fit tee fitting with three 1/4 inch connections, pack of 10

Legris

Legris 3103 56 14 Male Run Tee 1/4 in OD 290 PSI Pack of 10

SKU CH-PEFA-WSYNB MPN 3103

Push-fit tee connects three 1/4 in lines for air, cutting fluids or inert gases up to 290 PSI, includes pre-applied thread sealant, pack of 10

  • TypeDrain Components
  • ColorBlack
  • Push-to-connect ends speed up air-line assembly
  • Male NPT branch threads directly into 1/4 in ports
  • Pre-applied thread sealant cuts leak risk on installation
  • Fiberglass-reinforced nylon body resists cutting fluids and inert gases
  • Pack of ten fittings covers multiple connection points

Push-Fit Tee Fitting for Air and Fluids

This push-fit tee fitting connects three 1/4 inch lines in pneumatic and fluid systems. Two ends accept 1/4 inch outer diameter tubing with push-to-connect ports. The third end provides a 1/4 inch male NPT thread with pre-applied sealant. The body is moulded from black fibre-glass reinforced nylon. It is rated for 290 PSI and sold in a pack of 10.

Suits Pneumatic and Inert Gas Circuits

The fitting handles compressed air, cutting fluids and inert gases in industrial and automotive plumbing. It is not intended for potable water, high-temperature steam or aggressive chemical lines that exceed the nylon material limits. Installers needing a female thread, a different tube size or a metal body should select another part.

1/4 Inch Tube and Thread Size

Every port on this tee is sized for 1/4 inch connections: both push-to-connect ends take 1/4 inch OD tube and the threaded end is 1/4 inch male NPT. This single dimension determines whether the fitting matches your existing tubing and port requirements.

Highlights

  • Push-to-connect ends speed up air-line assembly
  • Male NPT branch threads directly into 1/4 in ports
  • Pre-applied thread sealant cuts leak risk on installation
  • Fiberglass-reinforced nylon body resists cutting fluids and inert gases
  • Pack of ten fittings covers multiple connection points

Specifications

TypeDrain Components
ColorBlack
BrandLegris
Model3103 56 14

Questions about this item

Will the 1/4 in OD push-to-connect ends on this 3103 56 14 tee seal reliably on the 1/4 in nylon tubing I already have installed?

Yes, both push-to-connect ports are sized for 1/4 in OD tube and use a fiberglass-reinforced nylon body with an internal collet and O-ring that grips and seals on standard 1/4 in nylon, polyurethane or polyethylene tubing.

How can I confirm the 1/4 MNPT branch on the 3103 56 14 is sealing properly after I thread it into my air line?

The branch has pre-applied thread sealant; after hand-tight plus one to two wrench turns, pressurise the system to working pressure and brush soapy water on the threads — no bubbles means the seal is holding.

Does the pack of 10 include any thread tape or tube inserts, or must I buy them separately?

The 10 tees come with thread sealant already on the 1/4 MNPT ends; no tape is needed there. Push-to-connect ends need no inserts for standard 1/4 in OD plastic tubing, so nothing extra is required for typical air or cutting-fluid lines.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.