We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Small black rectangular PoE splitter with RJ45 port Micro USB and USB C connectors on short cables

KINGARD

KINGARD Gigabit PoE Splitter 5V 3A 2-in-1 USB-C Micro USB 10/100/1000Mbps 802.3af/at

SKU CH-77WZ-PRQZ2

A Gigabit PoE splitter delivering 5V 3A to Micro USB and USB-C devices over a single Ethernet cable

  • TypeEthernet Adapter
  • Powers devices without nearby outlets using a single Ethernet cable
  • Delivers 5V 3A output with overvoltage, short-circuit and overcurrent protection
  • Supports 10/100/1000 Mbps data rates on Gigabit RJ45 ports
  • Includes Micro USB to USB-C adapter for 2-in-1 device compatibility
  • Works with Raspberry Pi 4B+/4B/3B+/3B, IP cameras, tablets and smart home devices

Gigabit PoE Splitter with 2-in-1 USB-C and Micro USB

This KINGARD splitter converts Power over Ethernet into a 5V 3A supply for devices that lack native PoE support. It carries both power and data over a single Ethernet cable from a PoE switch or injector. The unit targets Raspberry Pi boards, IP cameras, tablets and smart-home gear that need a simple wired connection without nearby mains outlets.

IEEE 802.3af/at compliance

The splitter meets the 802.3af and 802.3at standards and provides Gigabit Ethernet throughput through its RJ45 ports. This specification decides whether the unit will negotiate power correctly with your PoE source and pass full line-rate data to the attached device.

Plug-and-play adapter swaps Micro USB to USB-C

A supplied Micro-USB-to-USB-C adapter lets you change the output connector in seconds, so the same splitter serves boards and cameras with either port. No drivers or configuration are required. The only common issue is attempting to power equipment that draws more than the rated 5V 3A output, which triggers the built-in over-current protection.

Highlights

  • Powers devices without nearby outlets using a single Ethernet cable
  • Delivers 5V 3A output with overvoltage, short-circuit and overcurrent protection
  • Supports 10/100/1000 Mbps data rates on Gigabit RJ45 ports
  • Includes Micro USB to USB-C adapter for 2-in-1 device compatibility
  • Works with Raspberry Pi 4B+/4B/3B+/3B, IP cameras, tablets and smart home devices

Specifications

TypeEthernet Adapter

Questions about this item

What does the 5V 3A output actually deliver to a connected device?

The splitter converts PoE input into a steady 5 volt supply at up to 3 amps, powering Raspberry Pi boards, IP cameras or similar non-PoE gear through the USB-C or Micro USB port.

How do the 802.3af and 802.3at standards limit the power this unit can draw?

The splitter negotiates with any compliant PoE switch or injector under the af or at classes, so it only draws what the source allows while keeping the 5V 3A output protected against overvoltage and short circuits.

What physical connections and space are needed to install this splitter?

One RJ45 jack links to the PoE cable, and a short captive lead ends in Micro USB with a USB-C adapter attached — no extra mounting hardware, just room for the dongle beside the device.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.