We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Five packs of V-shaped three-pin JST SM cables with red green white wires

KEHIPI

KEHIPI 5 PCS JST SM 3PIN V Shape 1 to 2 Wire Cap Connectors 15CM 22AWG Pack of 2

SKU CH-1EY0-DETZQ

Pack of 2 sets, each with 5 V-shaped 3-pin JST SM splitters using 15 cm 22 AWG wire for 5 V–24 V addressable LED strips and controllers

  • Color MappingMulticolor
  • One female to two male 3-pin SM connectors simplify LED strip daisy-chaining
  • 15 cm 22AWG cables keep voltage drop low on 5 V to 24 V projects
  • Pre-crimped JST SM ends eliminate soldering for quick WS2811, WS2812B, SK6812 installs
  • Works with SP105E, SP611E and other 3-pin SPI controllers for plug-and-play control
  • Pack of 10 V-shape splitters gives plenty of branches for RGB, CCT or single-colour strips

Ready-to-use LED strip splitters

This pack supplies ten JST SM three-pin V-shape cables that split one female connector into two male ends. Each lead measures fifteen centimetres and uses 22AWG wire coloured red, green and white. They arrive new and ready to plug between addressable strips or between a controller and a strip without any soldering. Builders who need longer fixed looms or different pin counts should look elsewhere.

Three-pin JST SM interface

The single specification that decides fit is the three-pin JST SM V-shape connector with one female to two male ends. It matches WS2811, WS2812B, WS2814, SK6812 and FCOB WS2811 IC strips as well as SP105E, SP107E, SP108E, SP611E, SP602E, SP530E, SP630E, SP638E and DR03W controllers. Voltage must stay between five and twenty-four volts DC. Strips or controllers using four-pin, two-pin or non-JST headers will not connect.

Stable signal on extended runs

Manufacturer notes warn that signal instability and voltage drop can appear on long extension cables, showing as irregular flicker or dimmed output. The fifteen-centimetre length keeps resistance low, so sustained data throughput remains clean for typical indoor low-voltage projects. Users who chain many splitters or run strips far from the power source should inject power at intervals rather than rely on a single feed.

Highlights

  • One female to two male 3-pin SM connectors simplify LED strip daisy-chaining
  • 15 cm 22AWG cables keep voltage drop low on 5 V to 24 V projects
  • Pre-crimped JST SM ends eliminate soldering for quick WS2811, WS2812B, SK6812 installs
  • Works with SP105E, SP611E and other 3-pin SPI controllers for plug-and-play control
  • Pack of 10 V-shape splitters gives plenty of branches for RGB, CCT or single-colour strips

Specifications

BrandBTF-LIGHTING
Color MappingMulticolor

Questions about this item

What does the 3-pin V-shape layout mean when I plug it into my LED strip?

One female connector splits into two male connectors so a single controller output can drive two separate 3-pin addressable strips.

Which controller models are confirmed to work with the JST SM interface on these cables?

Compatible controllers include SP105E, SP107E, SP108E, SP611E, SP602E, SP530E, SP630E, SP638E and DR03W.

How much space should I allow for the 15 cm cables and 22 AWG wire when routing them inside a channel?

Each pigtail is about 5.9 inches long with 22 AWG conductors, so allow a little extra slack for the split and the connector bodies.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.