We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black plastic speaker pods with 6.5 inch neodymium drivers, left and right pair, Jeep dash fit

DS18

DS18 JP6 6.5" Neodymium Dash Speaker Pods for Jeep JL/JLU/JT

SKU CH-CQ4G-S6GZ9

Plug-and-play dash pods with 6.5" neodymium speakers deliver 150 W RMS and 300 W peak for Jeep JL, JLU and JT models

  • Type2-way Speaker
  • Speaker Size3"
  • Plug-and-play kit installs in under 30 minutes with basic hand tools
  • 5" neodymium mid-range drivers deliver 150 W RMS and 300 W peak power
  • High 96 dB sensitivity produces louder output from factory or aftermarket amplifiers
  • Frequency response of 100 Hz to 10 000 Hz covers critical mid-range detail
  • Designed specifically for Jeep JL, JLU and JT dash locations

Jeep JL/JLU/JT Dash Speaker Pods

The DS18 JP6 kit provides a direct-fit front speaker upgrade for Jeep JL, JLU and JT Gladiator models. It includes left and right enclosures pre-assembled with 6.5 inch neodymium mid-range drivers rated at 150W RMS and 300W peak power. The 2-way design targets 96dB sensitivity across a 100Hz to 10,000Hz response.

Verify Factory Wiring and Amplifier

Confirm your vehicle uses the standard wiring harness that the pods plug into without adapters. The speakers present a 4 ohm impedance and 3.2 ohm DC resistance, so the factory amplifier must be stable at that load. A high-pass crossover set near 120Hz is recommended to protect the 1.5mm excursion limit.

Steel Basket Enclosures with Neodymium Magnets

Each pod uses a steel basket and a 3 oz neodymium magnet for a compact, rigid mount that bolts into the original dash locations. Paper cones with cloth surrounds and 1.5 inch Kapton voice coils handle the 138Hz free-air resonance. The pre-wired terminals connect to the factory plugs for a solder-free install.

Highlights

  • Plug-and-play kit installs in under 30 minutes with basic hand tools
  • 5" neodymium mid-range drivers deliver 150 W RMS and 300 W peak power
  • High 96 dB sensitivity produces louder output from factory or aftermarket amplifiers
  • Frequency response of 100 Hz to 10 000 Hz covers critical mid-range detail
  • Designed specifically for Jeep JL, JLU and JT dash locations

Specifications

Type2-way Speaker
Speaker Size3"

Questions about this item

What comes in the DS18 JP6 box and is anything else required?

The kit includes left and right 6.5" neodymium speakers pre-mounted in dash pods with wiring harnesses for a true plug-and-play fit in Jeep JL, JLU and JT models; no extra parts are needed for a factory-amp installation.

Which power rating should I use when matching an amplifier to these speakers?

Use the 150W RMS figure per speaker for amplifier matching; the 300W peak rating only describes short-term burst capability.

What does the 96dB sensitivity mean once the speakers are installed in my Jeep?

At 96dB sensitivity the speakers produce high output with modest power, so the factory amplifier can drive them loudly and an aftermarket amp will yield even greater volume.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.