We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Condor 30HG97 body belt XL with padding and two hip D-rings

Condor

Condor 30HG97 Body Belt XL 46-55 in 2 D-Rings traffic safety equipment

SKU CH-SRKZ-YDJ4W

Extra-large padded body belt with two hip D-rings, fitting waists 46-55 inches and rated to 425 lb, meeting OSHA 1910.66 and 1926.502

  • Supports up to 425 lb with steel hardware
  • Fits waists 46 to 55 in for XL sizing
  • Meets OSHA 1910.66 and 1926.502 fall-protection standards
  • Two hip D-rings give secure tie-off points
  • Padded polyester webbing adds comfort during extended wear

Industrial fall-protection belt

The Condor 30HG97 is an XL body belt built for workers who need a secure hip attachment point while positioning or restraining on structures. It fits waist sizes from 46 in to 55 in and uses a tongue buckle for quick adjustment. Two steel D-rings at the hips give a reliable tie-off location for lanyards or positioning devices. The 425 lb weight capacity supports a broad range of users and tools.

Polyester webbing and steel hardware

Uncoated polyester webbing resists abrasion and UV exposure without adding bulk or stiffness. The steel D-rings and buckle maintain strength after repeated loading cycles. Padding is included to reduce pressure on the hips during long shifts. No electronic tracking is fitted, so the belt stays simple and inspection is straightforward.

Replaces worn or undersized positioning belts

Crews moving up from narrower belts gain the 46 in to 55 in adjustment range without changing lanyard hardware. The jump is worth it when the current belt no longer meets OSHA 1910.66, OSHA 1926.502 or the referenced A 10.32 and Z 359 standards. Workers who need shoulder D-rings or integrated RFID tracking should look at a full harness instead.

Highlights

  • Supports up to 425 lb with steel hardware
  • Fits waists 46 to 55 in for XL sizing
  • Meets OSHA 1910.66 and 1926.502 fall-protection standards
  • Two hip D-rings give secure tie-off points
  • Padded polyester webbing adds comfort during extended wear

Specifications

BrandCONDOR

Questions about this item

How do I put the 30HG97 body belt on and what step do people miss?

Thread the polyester webbing through the steel tongue buckle so the padded section sits on the hips with both D-rings forward, then pull the strap until the belt is snug between the 46 in minimum and 55 in maximum waist range; the step most people miss is verifying the tongue is fully seated in the buckle before clipping a lanyard.

What part of the 30HG97 body belt will need replacement first?

The uncoated polyester webbing and steel hardware should be inspected before every use; replace the belt immediately if you find cuts, abrasion, UV damage, deformed D-rings, or a tongue buckle that no longer locks securely.

What is the first limit I will hit when wearing the 30HG97 body belt all day?

The belt is rated to a 425 lb weight capacity and meets OSHA 1910.66, 1926.502 and ANSI Z359.1, Z359.12, A10.32 standards, so the practical limit under sustained wear is the 46 in to 55 in waist adjustment range — if your waist measurement falls outside that span the belt cannot be worn safely.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.