We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Small rectangular nickel-zinc battery pack with wire connector, 77 by 48 by 11 mm, labelled 500mAh 3.6V

Cameron Sino LK NEO MHM03 500mAh 3.6V nickel-zinc battery

SKU CH-5B11-PG003

500 mAh nickel-zinc replacement battery for Autec LK NEO crane remote controls, 3.6 V and 1.80 Wh in a 77.06 × 48.04 × 11.00 mm pack

  • Specifications77.06 x 48.04 x 11.00
  • Typenickel_zinc
  • Battery Pack77.06 x 48.04 x 11.00
  • Battery Typenickel_zinc
  • Battery Capacity500.00 milliamp_hours
  • Battery Voltage3.60 volts
  • 500mAh capacity powers longer RC flights
  • 6V nickel-zinc chemistry matches original specs
  • 06 x 48.04 x 11.00mm fits Autec LK NEO crane remote
  • ISO9001, RoHS and CE certified for safety
  • Fully decoded chip works like the original battery

Replacement Battery for Autec LK NEO Crane Remote

This 500mAh nickel-zinc pack replaces the original MHM03 or R0BATT00E11A0 cell in Autec LK NEO crane remote controls. It delivers 3.6 volts and 1.80 watt-hours in a 77.06 by 48.04 by 11.00 millimetre form factor weighing 54.2 grams. The built-in decoded chip communicates with the handset exactly like the factory unit. Buyers needing a different voltage or chemistry should look elsewhere.

Sustained Output and Protection

Nickel-zinc chemistry maintains a stable 3.6 volt nominal level through the discharge curve rather than sagging under load. Integrated circuitry guards against overcharge, over-discharge, over-voltage and short-circuit events during extended operating sessions. The pack reaches full performance after two or three complete charge cycles. Users who require hot-swap capability or parallel-cell configurations will not find those features here.

Compatibility Check Before Ordering

Verify that your crane remote bears the Autec LK NEO name and that the original battery carries part number MHM03 or R0BATT00E11A0. Confirm the connector orientation matches the keyed plug on this replacement. Ensure your charger is designed for nickel-zinc cells; low-quality third-party adapters can shorten service life. Installers uncomfortable with small-electronics disassembly should seek professional assistance.

Highlights

  • 500mAh capacity powers longer RC flights
  • 6V nickel-zinc chemistry matches original specs
  • 06 x 48.04 x 11.00mm fits Autec LK NEO crane remote
  • ISO9001, RoHS and CE certified for safety
  • Fully decoded chip works like the original battery

Specifications

BrandCameron Sino
ModelLK NEO
Part NumberMHM03, R0BATT00E11A0
Specifications77.06 x 48.04 x 11.00
Typenickel_zinc
Battery Pack77.06 x 48.04 x 11.00
Battery Typenickel_zinc
Battery Capacity500.00 milliamp_hours
Battery Voltage3.60 volts

Questions about this item

Does the 3.6 V nickel-zinc cell run hot during a full day of crane remote use?

The pack is rated at 3.6 V and 500 mAh; nickel-zinc chemistry typically stays cool under the modest draw of a handheld remote.

What charger or connector must I already have to use this MHM03 pack?

It fits the Autec LK NEO remote and uses the original connector; you need the stock charger that came with that remote.

Will this 77.06 × 48.04 × 11.00 mm battery work in an older Autec remote that still takes the original MHM03?

Yes, it matches the exact dimensions and part numbers MHM03 and R0BATT00E11A0 for direct replacement.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.