We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Yellow rectangular Li-MnO2 battery 52 by 50 by 25 mm

Cameron & Co

Cameron & Co DS-CS-FN006SL Li-MnO2 5 Ah 6.0V Yellow standard battery

SKU CH-79VV-VPF68

A 6.0 V, 5 Ah lithium-manganese dioxide primary cell sized 52.00 x 50.50 x 25.00 mm for Panasonic BR-CCF2TH and Fanuc A06 series PLCs

  • TypePower Tool
  • Li-MnO2 chemistry provides stable 6.0 V output
  • 5 Ah capacity delivers 30.00 Wh for extended runtime
  • Direct replacement for Panasonic BR-CCF2TH and Fanuc A06 series PLCs
  • Compact 52.00 x 50.50 x 25.00 mm form fits existing battery compartments
  • Non-rechargeable primary cell ensures reliable backup power for industrial controllers

Replacement for A06-series PLC backup

This lithium-manganese dioxide cell delivers 6.0 V and 5 Ah to Panasonic BR-CCF2TH, Cutler Hammer A06 and GE Fanuc A06 programmable controllers. It matches part numbers A06B-6073-K005, A98L-0031-00012 and the Mori Seiki CS-FN006SL reference. The yellow housing identifies the correct polarity at a glance.

Steady voltage during long memory-hold

Li-MnO2 chemistry maintains a flat discharge curve so the PLC retains ladder logic and retained variables across months of power-off periods. Rated capacity of 5000 mAh supports extended backup intervals without the voltage sag seen in alkaline alternatives. Non-rechargeable design eliminates charging-circuit failures.

Direct drop-in for control cabinets

The 52.00 x 50.50 x 25.00 mm case slides into the existing battery compartment on A06, A06B-0073-K001 and TL3000 units without adapters. Polarity markings on the yellow sleeve prevent reverse insertion, the most common cause of controller fault codes. Single-cell construction means no balancing or connector wiring is required.

Highlights

  • Li-MnO2 chemistry provides stable 6.0 V output
  • 5 Ah capacity delivers 30.00 Wh for extended runtime
  • Direct replacement for Panasonic BR-CCF2TH and Fanuc A06 series PLCs
  • Compact 52.00 x 50.50 x 25.00 mm form fits existing battery compartments
  • Non-rechargeable primary cell ensures reliable backup power for industrial controllers

Specifications

BrandCameron Sino
ModelDS-CS-FN006SL
TypePower Tool

Questions about this item

Does the 6.0 V 5 Ah Li-MnO2 cell generate noticeable heat during continuous PLC operation?

The primary lithium chemistry runs cool under the low-current draw of A06 series controllers; no active cooling is required.

Must I already own a Panasonic BR-CCF2TH or Fanuc A06B-6073-K005 slot for this battery to fit?

Yes — the 52.00 × 50.50 × 25.00 mm yellow pack is a direct mechanical and electrical match for those part numbers only.

Will this non-rechargeable 30.00 Wh unit work alongside the older A98L-0001-0902 backup cells I still have in stock?

It replaces those cells one-for-one; do not mix fresh and depleted units in the same holder.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.