We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Compact six-port PoE+ switch in fanless metal housing

BFKK

BFKK 6-Port PoE+ Switch 4×PoE+ 2×Uplink 65W Fanless Metal

SKU CH-9XW2-RQT69

Unmanaged 6-port switch with four PoE+ ports up to 30 W each, two uplink ports, 65 W total budget and 250 m extend mode

  • Four PoE+ ports power devices up to 30 W each with a 65 W total budget
  • Two 10/100 Mbps uplink ports connect the switch to the wider network
  • Extend mode stretches PoE reach to 250 m at 10 Mbps for distant cameras
  • Fanless metal chassis operates silently from -20 °C to 50 °C
  • AI watchdog auto-reboots unresponsive PoE devices and one-key VLAN isolates ports 1-4

6-Port PoE+ Switch for IP Cameras and Access Points

This six-port unmanaged switch delivers four PoE+ ports and two Fast Ethernet uplinks for small surveillance or wireless deployments. Each PoE+ port supplies up to 30 watts while the total power budget reaches 65 watts. The fanless metal enclosure operates silently in offices or sheltered outdoor cabinets.

Fast Ethernet limits and 250-metre extend mode

All six ports run at 10/100 Mbps, so aggregate throughput peaks at 1.2 Gbps with a packet rate of 0.8928 Mpps. Enabling extend mode drops PoE ports to 10 Mbps but pushes the cable reach to 250 metres using Cat5 or better UTP. Jumbo frames are capped at 2 Kbytes and the MAC table holds 1 K entries.

Check power budget and VLAN needs before ordering

Verify that the combined draw of your PoE devices stays within the 65-watt ceiling, noting the 15.4-watt baseline per 802.3af device. The one-key VLAN isolates ports one to four from each other while keeping uplink access, which may break device-to-device traffic. The switch requires AC 100-240 V input and operates from -20 °C to 50 °C.

Highlights

  • Four PoE+ ports power devices up to 30 W each with a 65 W total budget
  • Two 10/100 Mbps uplink ports connect the switch to the wider network
  • Extend mode stretches PoE reach to 250 m at 10 Mbps for distant cameras
  • Fanless metal chassis operates silently from -20 °C to 50 °C
  • AI watchdog auto-reboots unresponsive PoE devices and one-key VLAN isolates ports 1-4

Specifications

No published specifications for this item yet.

Questions about this item

Should I pick the 4-port PoE+ model or a larger PoE switch for my cameras?

This unit provides four 10/100 Mbps PoE+ ports with a 30 W per-port limit and a 65 W total budget, plus two 10/100 Mbps uplink ports for the NVR or router.

What does the 65 W power budget mean when I connect four IP cameras?

You can run four cameras drawing up to 30 W each, but the combined draw must stay at or below 65 W; the switch will not exceed that total.

The uplinks are only 10/100 Mbps — will that bottleneck my 1 Gbps router?

Yes, the two uplink ports operate at 10/100 Mbps, so any traffic passing through them is capped at 100 Mbps regardless of the router speed.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.