We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Handheld 4 inch CCTV tester with keypad and screen

BFKK

BFKK 5 in 1 CCTV Tester 4 inch Screen Keypad POE Out PTZ

SKU CH-JBGR-AD8R3

Handheld 4‑inch tester checks 8MP TVI, 4MP CVI, 5MP AHD, CVBS and 4K IP cameras, supplies 12V DC and 48V PoE, and controls PTZ via over 30 protocols

  • TypeOther
  • Tests up to 8MP analog and 4K IP cameras
  • Powers devices with 12V DC and 48V PoE up to 24W
  • 4 inch 800×480 screen with keypad for portable use
  • 4V 2400mAh battery gives about 8 hours runtime
  • Controls PTZ via coaxial with over 30 protocols

Installation and maintenance tool

The BFKK 5 in 1 CCTV tester is built for technicians who install and maintain IP analog, HD coaxial and CVBS cameras. It combines a 4 inch screen with a physical keypad in a handheld form factor. The unit provides DC12V 1A and PoE DC48V power outputs up to 24W for powering cameras during setup. A 7.4V 2400mAh battery delivers about 8 hours of operation after a 4 to 5 hour charge.

Sustained field operation

The tester runs on its internal lithium ion polymer battery for roughly 8 hours per charge, supporting full day use on site without mains power. It supplies up to 24W through PoE and 12V outputs continuously while testing multiple cameras in sequence. Ethernet testing at 10/100/1000M, PING, IP scan and port flashing remain responsive during extended sessions. Audio recording, LED lamp and built in utilities stay available throughout the work period.

8MP TVI and 4K IP camera support

The single specification that decides fit is the maximum analog resolution of 8MP for TVI, 4MP for CVI and 5MP for AHD, plus H.265 and H.264 IP camera decoding up to 4K. If the installation uses cameras beyond these limits, the tester cannot display or configure them. Buyers who need higher analog megapixel counts or newer IP codec profiles must select a different instrument.

Highlights

  • Tests up to 8MP analog and 4K IP cameras
  • Powers devices with 12V DC and 48V PoE up to 24W
  • 4 inch 800×480 screen with keypad for portable use
  • 4V 2400mAh battery gives about 8 hours runtime
  • Controls PTZ via coaxial with over 30 protocols

Specifications

TypeOther

Questions about this item

How much heat or noise does the tester produce when running continuously on its 7.4 V 2400 mAh battery for a full shift?

The unit is fanless and battery-powered, so it generates no audible fan noise and only minimal warmth during an 8-hour working cycle.

What additional equipment is required before the tester can power and display a 4K IP camera?

A charged 7.4 V battery, a Cat5e or better Ethernet cable, and the camera’s login credentials are all that is needed; the tester supplies PoE 48 V up to 24 W itself.

Will the on-screen PTZ menu drive a legacy Pelco-D dome that I still have installed?

Yes, the tester supports more than 30 PTZ protocols including Pelco-D, Pelco-C, Samsung, Panasonic, Lilin and Yaan over coaxial control.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.