We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Coiled black polyurethane tubing, 100 ft length, 5/32 in ID 1/4 in OD

Atp

Atp PU25-ABLK Trap 5/32 in ID 1/4 in OD 100 ft Black Polyurethane

SKU CH-8VTJ-FZN91 MPN PU25-ABLK

Black polyurethane tubing with a 5/32 in inside diameter and 1/4 in outside diameter, rated for 180 psi and 140 °F across a 100 ft coil

  • TypeDrain Components
  • ColorBlack
  • Durable polyurethane resists abrasion and wear
  • 100 ft coil covers long runs without joints
  • 180 psi rating handles demanding air and water lines
  • Operates up to 140 Degrees F for hot-fluid use
  • Shore A 98 hardness keeps shape under pressure

Black polyurethane tubing for air and water lines

This 100 ft coil of black polyurethane tubing serves automotive and general plumbing circuits that carry air or water. The 5/32 in inside diameter and 1/4 in outside diameter suit push-to-connect fittings and barbed nipples commonly found on shop airlines and fluid-transfer kits. Buyers who need larger-bore hose or a different material should look elsewhere.

Shore A 98 hardness handles 180 psi at 140 Degrees F

The polyurethane wall is rated to a maximum operating pressure of 180 psi and a maximum operating temperature of 140 Degrees F. Shore A 98 hardness resists kinking and holds shape under normal shop pressure cycles without softening. The tubing is not rated for higher temperatures or pressures beyond these limits.

Abrasion and wear resistant with no jacket

A single-layer polyurethane construction provides abrasion and wear resistance without an outer jacket. The smooth black surface resists scuffing when routed across frames or through cable tracks. Peristaltic pump compatibility is not supported, so the tubing should not be specified for roller-pump applications.

Highlights

  • Durable polyurethane resists abrasion and wear
  • 100 ft coil covers long runs without joints
  • 180 psi rating handles demanding air and water lines
  • Operates up to 140 Degrees F for hot-fluid use
  • Shore A 98 hardness keeps shape under pressure

Specifications

TypeDrain Components
ColorBlack
BrandATP
ModelPU25-ABLK

Questions about this item

How do I install the 5/32 in ID polyurethane tubing without kinking it?

Cut the 100 ft coil to length with a sharp tube cutter, push the 1/4 in OD end firmly onto the barbed fitting until it seats against the shoulder, and secure with a hose clamp; the common mistake is forcing a tight bend near the fitting, which collapses the 98 Shore A wall and restricts flow.

What maintenance or replacement will the black polyurethane tubing need over time?

Inspect the 100 ft length periodically for surface abrasion, UV discolouration, or hardening above 140 °F; replace any section that shows cracks, permanent deformation, or loss of the original 180 psi pressure rating.

What is the first limit reached when the tubing runs continuously at high pressure?

The 180 psi maximum operating pressure is reached before the 140 °F temperature ceiling under sustained use, so pressure relief or a regulator must be set below 180 psi to avoid burst risk.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.